626808
18
Zoom out
Zoom in
Vorherige Seite
1/23
Nächste Seite
16
BLENDER JAR IS DISHWASHER SAFE—TOP RACK ONLY!
Extreme temperatures damage the lower seal of the jar� We recommend hand
washing to prolong the life of the blender jar� We do not recommend the jar be
used for temperatures abo boiling (212°F, 100°C)�
SECTION 7: TROUBLESHOOTING
While we don’t expect you to have any problems with your blender, sometimes
failures do occur� Use the following guidelines to see if the problem is easily fixed
or requires service�
7.1 BLENDER MOTOR WILL NOT TURN ON (NO POWER)
If the blender motor will not turn on, try the following:
Determine if the Power Button is lit� Absence of a lit Power Button indicates a lack of
power to the unit
Make sure the blender is plugged in
Check your house circuit breaker switch or fuse to make sure it is set to the
ON position�
Press the Power Button located on the upper right hand side of the touch area
Unplug the power cord from the wall receptacle, wait 5 seconds, then plug
power
cord back in�
7.2 ERROR MESSAGES ON DISPLAY
If this icon appears on your blender, it indicates that the motor is overheating� The
blender has been disabled until the unit cools to operating temperatures� Turn off
and unplug the unit� Allow it to cool for at least 20 minutes, then plug it back into
check if the icon is still visible� If the icon does not disappear after 20 minutes or
more of cooling time, please call your Blendtec Service Agent�
If this icon appears on your blender, please turn off and unplug the unit� Check the
blender jar for blockage and clear if necessary� Plug in the unit and turn the blender
on again� If the icon is still visible on your blender, contact your Blendtec Service
Agent�
If this icon appears on your blender it indicates that more than one touch sensor
on the blender has been touched� This icon should only appear as long as the
multiple sensor areas are being touched� If this icon remains on when no one is
touching the touch area unplug and re-plug in the blender� If the problem persists
please contact your Blendtec Service Agent�
If this message appears on the LED information center it indicates there has been
an error� There are error messages from E-01 through E-06� If any of these errors
appear, press the stop button to clear the message� If the error message reappears
please contact your Blendtec Service Agent�
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Blendtec DESIGNER 625 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Blendtec DESIGNER 625

Blendtec DESIGNER 625 Bedienungsanleitung - Deutsch, Englisch, Französisch - 40 seiten

Blendtec DESIGNER 625 Bedienungsanleitung - Französisch - 22 seiten

Blendtec DESIGNER 625 Bedienungsanleitung - Spanisch - 40 seiten

Blendtec DESIGNER 625 Bedienungsanleitung - Spanisch - 26 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info