Bedienungsanleitung Blendtec Q-Series (Seite 10 von 16) (Englisch)

773994

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

become blunt, but there is no problem with the mixing power. (The blade is

not sharp.)

• RUNNING SOCKET: The running socket (Refer to Figure 1.2) is subject to

the warranty during the lifecycle of the product.

• The warranty is applied from the delivery date or the purchasing date when

the purchasing certiﬁcate is submitted. (The apparent defect or the damage

caused by misuse is not subject to the warranty.)

72. SOLUTIONS FOR POTENTIAL PROBLEMS

WHEN THE MOTOR OF THE BLENDER DOES NOT ROTATE, CHECK THE

FOLLOWING CONTENTS.

• Check whether the main power switch on the lower part of the front is on or

not.

• Check whether the power switch of the fuse box in your house or store is on

or not.

• Pull out the power cord and put it in the outlet again.

• Check whether the LCD screen shows light. (If there is no light, there would

be not enough power for the micro-processor or it would be broken. In such a

case, you must have your product ﬁxed.)

WHEN THE LEVEL OF NOISE FOR THE BLENDER HAS INCREASED

GREATLY IN COMPARISON WITH THE INITIAL LEVEL.

• When the bearing of the jar has been worn out and its lifecycle has been

ended, the level of noise becomes great. (Replace the jar. If you are still in the

warranted period, you can have your defected product replaced.)

• When there is a scratching sound coming from the motor, the lifecycle of the

component of the internal brush has been ended. (You can make an inquiry

at the repairing center of our blender products and have your product or

component replaced.)

• If a loud sound is heard when operating the jar after pulling it out the motor,

you can make an inquiry at the repairing center of our blender products.

WHEN THERE IS SOMETHING WRONG WITH THE MOTOR OF THE

BLENDER, CHECK THE LCD SCREEN. (When there is something wrong with

the motor of the blender, an error message appears on the LCD screen.)

• When ‘OVERTEMP’ appears on the LCD screen: The motor is overheated. In

such a case, the motor can be operated again when the internal temperature

of the motor is decreased to the one for the possible operation. (Pull out

the power cord and cool the motor down for 20 minutes before operating it

again.)

• When ‘OVERLOAD’ appears on the LCD screen: The motor is overloaded.

Keep the switch turned off for 10 seconds. After checking the factors which

disrupt the movement among the blades of the jar, operate it again.

• (If ‘OVERLOAD’ still appears on the LCD screen, or the moving sound is

different from the previous one, have your product repaired.)

• When ‘LOW VOLTAGE’ appears on the LCD screen: There is not enough

power supplied by the motor. Turn off the motor and solve the cause for the

low voltage. (Such a problem usually occurs when the power extension is

used for one power outlet.)

THERE IS A LUMP OR PIECE OF ICE LEFT STILL AFTER THE BLENDING

Downloaded from www.Manualslib.com manuals search engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blendtec Q-Series Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info