Bedienungsanleitung Blendtec Signature Series (Seite 8 von 11) (Englisch)

626835

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

1110

SECTION 6: CLEANING

6.1 AFTER-USE CLEANING

• Add 1 cup of hot water and 1 drop of liquid dish soap to the blender jar�

• Place the lid tightly on the jar� Place the jar on the blender base and press

“Pulse” for 5 seconds�

• Rinse with clean water until all soap is rinsed from the jar and lid�

• Place the jar and lid on a dish rack or dry by hand with a soft cloth�

• Unplug the blender base and clean it by wiping the base and control surface

with a damp cloth�

6.2 LONG-TERM SANITATION

• For long-term sanitation, ﬁll the blender jar with hot water�

• Add appropriate amount of liquid chlorine bleach�

• Stir for 10 seconds� Let the mixture stand in the jar for 5 minutes�

• Empty the water/bleach mixture� Turn the jar upside down on a dish rack to dry�

6.3 CLEANING TIPS AND CAUTIONS

• Do not use stiff-bristled brushes or abrasive cloths/pads to clean the

blender base or jar; using such materials will scratch and dull the surface�

• Never submerge the blender motor base in water� Avoid submerging

the blender jars for more than 5 minutes� If water penetrates the lower jar

seals, the life of the jar will decrease�

• The blender jar is dishwasher safe on the top rack only� However,

extreme temperatures (over 185ºF, 85ºC) can damage the jar material�

Blendtec recommends hand-washing the jar to prolong the life of the jar�

SECTION 7: TROUBLESHOOTING

While Blendtec does not expect you to have any problems with your blender,

sometimes failures do occur� Use the following guidelines to troubleshoot any issues�

7.1 NO POWER

If the blender motor will not turn on, try the following:

• Determine whether the LCD display is lit� If the LCD display is not lit, the

unit lacks power�

• Ensure the main power switch on the back is turned on�

• Check your house circuit breaker switch or fuse to ensure it is set to the

ON position�

• Unplug the power cord, wait 5 seconds and then plug the cord back in�

• If blender still fails to function, call 1-800-BLENDTEC or 801-222-0888�

7.2 ERROR MESSAGES

• Overload: This message indicates an overload on the motor� Turn off

and unplug the unit� Remove the blender jar from the motor base, and

turn the shaft by hand to ensure the blade turns freely� If the blade does

not move freely, check for any obstruction in the jar� The problem may

also be the jar itself, not the motor� If the blade moves freely, plug in

the unit and turn the blender on� If the overload condition reoccurs, call

1-800-BLENDTEC or 801-222-0888 for further assistance�

• Overtemp: This message indicates that the motor is overheating� The

blender has been disabled until the unit cools to operating temperature�

Turn off and unplug the unit� Allow it to cool for at least 20 minutes�

• E-05 (Reset Error): This message indicates a permanent failure of the

electronics in the unit� Call 1-800-BLENDTEC for repair/replacement (see

Section 8: Warranty)�

• E-04 (No Zero Crossing): This message indicates failure of a component

on the electronic board� Call 1-800-BLENDTEC for repair/replacement

(see Section 8: Warranty)�

7.3 NOISE-LEVEL CHANGES

If the blender noise has increased from the original levels, determine

whether the sound is coming from the blender motor or jar�

• Blender motor: Remove the jar, and press “Pulse” � Listen to the

motor� If it is excessively noisy, call 1-800-BLENDTEC for evaluation�

• Jar: After checking the motor, ﬁll the jar with 2 cups of water and

place back on the motor base� Run the blender for a few seconds by

pressing � If you have more than one jar, test a different jar to

determine whether the sound is different� If a jar is exces sively noisy, or

if the blade assembly seems loose or sounds gravelly when turned by

hand, call 1-800-BLENDTEC�

7.4 UNSATISFACTORY BLENDED TEXTURE

If the blended texture of the mixture is lumpy or uneven, do the following:

• Ensure the mixture is not cavitating during the cycle� Cavitation is a

condition in which an air pocket forms in the mixture because the

mixture is too cold or too solid, causing the blender blade to spin freely�

To correct this problem, increase the mixture temperature by reducing

the ice, increasing the liquid and/or ensuring the frozen ingredients

used in the recipe are not too cold�

• If the recipe is mixing well but has not had enough time to completely

blend, try a longer cycle or touch and hold “Pulse” for extra blending time�

• If none of the preceding suggestions work, call 1-800-BLENDTEC�

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blendtec Signature Series Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blendtec Signature Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info