Bedienungsanleitung Blendtec Total Blender Designer Series (Seite 8 von 11) (Englisch)

626837

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

1514

7.2 BLENDER MOTOR WILL NOT TURN ON

If the blender motor will not turn on, try the following:

• Determine if the Power Button is lit� Absence of a lit Power Button indicates a

lack of power to the unit�

• Make sure the blender is plugged in�

• Check your house circuit breaker switch or fuse to make sure it is set to the ON position�

• Press the Power Button located on the upper right hand side of the touch area�

• Unplug the power cord from the wall receptacle, wait 5 seconds, then plug

power cord back in�

Look at the Touch Area:

If this icon appears on your blender, it indicates that the motor is overheating� The

blender has been disabled until the unit cools to operating temperatures� Turn off

and unplug the unit� Allow it to cool for at least 20 minutes, then plug it back in

to check if the icon is still visible� If the icon does not disappear after 20 minutes

or more of cooling time, please call your Blendtec Service Agent�

If this icon appears on your blender, please turn off and unplug the unit� Check

the blender jar for blockage and clear if necessary� Plug in the unit and turn the

blender on again� If the icon is still visible on your blender, contact your Blendtec

Service Agent�

If this icon appears on your blender it indicates that more than one touch sensor

on the blender has been touched� This icon should only appear as long as the

multiple sensor areas are being touched� If this icon remains on when no one

is touching the touch area unplug and re-plug in the blender� If the problem

persists please contact your Blendtec Service Agent�

If this message appears on the LED information center it indicates there has

been an error� There are error messages from E-01 through E-06� If any of these

errors appear, press the stop button to clear the message� If the error message

reappears please contact your Blendtec Service Agent�

7.3 NOISE LEVEL CHANGES

If the blender noise level has increased signiﬁcantly from original levels, determine

whether the sound is coming from the blender motor or jar�

• Blender Motor: Check to see if the excess noise is coming from the blender

base� Remove the jar and press Ice Crush or Smoothie button� Listen to the

motor sound without a jar attached� If it is excessively noisy contact your

Blendtec Service Agent�

• Jar: Check to see if the excess noise is coming from the jar� Run the blender

for a few seconds using the Pulse Button� If you have more than one jar, test a

different jar to determine whether the sound changes as different jars are used�

If a jar is excessively noisy, or if the jar shaft assembly seems loose or feels

rough when turned by hand, contact your Blendtec Service Agent�

SECTION 6 - CARE AND CLEANING

6.1 AFTER USE CLEANING

1� Add 1 cup (240 ml) of hot water and a drop of liquid dishwashing soap to

the blender jar�

2� Place the lid tightly onto the jar� Place the blender jar on the blender base and,

with your hand placed on top of the lid, press the pulse button for 5 seconds�

3� Rinse with clear water until all soap is rinsed from jar and lid�

4� Clean the blender base by simply wiping the base and touchpad with a damp cloth�

6.2 LONG-TERM SANITATION

1� For long-term sanitation, ﬁll the blender jar with hot water�

2� Add one teaspoon (5 ml)of liquid chlorine bleach�

3� Stir for 10 seconds to mix water and bleach� Let mixture stand in blender jar for

5 minutes�

4� Empty water/bleach mixture� Turn jar upside down on dish rack until dry�

6.3 CLEANING TIPS AND CAUTIONS

• Do not use abrasives or stiff brushes to clean the blender base or jar as this will dull

or scratch the surface� Cosmetic damage is not covered by warranty�

• NEVER submerge the blender motor in water� Avoid submerging blender jars for

more than 5 minutes� Water penetration through the lower jar seals will reduce the

life of the jar�

• BLENDER JAR IS DISHWASHER SAFE—TOP RACK ONLY! Extreme temperatures

damage the lower seals of the jar� We do not recommend the jar be used for

temperatures above boiling (212°F, 100°C)�

SECTION 7 - TROUBLESHOOTING

7.1 BLENDED TEXTURE UNSATISFACTORY

If the blended texture of product is lumpy or uneven, do the following:

• Ensure the mixture is not cavitating during the cycle� Cavitation is a condition in

which the blender blade spins freely in an air pocket within the drink mix because

the mix is too cold or too solid� This problem can be corrected by increasing

the mix temperature by reducing ice, increasing liquid, and/or ensuring that

the frozen ingredients used in the recipe are never colder than 10 degrees

Fahrenheit (-12 degrees Celsius)�

• Increase cycle time� If the drink is mixing well but has not had enough time for

complete blending, try a longer cycle or touch and hold the “Pulse” icon for extra

blending time�

• TRIED EVERYTHING? If none of the preceding suggestions work, contact your

Blendtec Service Agent for further assistance�

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blendtec Total Blender Designer Series Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blendtec Total Blender Designer Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info