Bedienungsanleitung Blomberg TKF 8431 A (Seite 5 von 68) (Englisch, Dänisch)

582140

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

2 Installation

Refer to the nearest Authorised Service Agent

for installation of your product.

C Preparation of location and electrical

installation for the product is under

customer’s responsibility.

BInstallation and electrical connections must

be carried out by a qualified personnel.

A Prior to installation, visually check if the

product has any defects on it. If so, do not

have it installed. Damaged products will

cause risks for your safety.

Appropriate installation location

• Install the product in an environment which

has no risk of freezing and is in a stable and

level position.

• Operate your product in a well ventilated,

dust-free environment.

• Do not block the air ducts in front of and

under the product with materials such as

long pile rugs and wooden bands.

• Do not place your product on a long pile rug

or on similar surfaces.

• Do not install the product behind a door

with a lock, sliding door or a hinged door

which can strike the product.

• Once the product is installed, it should stay

at the same place where its connections

have been made. When installing the

product, make sure that the rear wall of it

does not touch anywhere (tap, socket, etc.)

and also pay attention to install the product

at a place where it will stay permanently.

B Do not place the product on top of the

power cable.

• Keep at least 1.5 cm distance to walls of

other furniture.

Removing the transportation

safety assembly

ARemove the transportation safety assembly

before using the product for the first time.

1. Open the loading door.

2. There is a nylon bag inside the drum that

contains a piece of styrofoam. Hold it from

its section marked with XX.

3. Pull the nylon towards yourself and remove

the transportation safety assembly.

AMake sure that you have removed

the transportation safety assembly

(nylon+styrofoam pieces) before using the

product for the first time. Do not leave any

items inside the drum.

Under counter installation

• A special part (Part no. 297 360 0100)

replacing the top trim must be provided and

installed by the Authorised Service Agent in

order to use the machine under a counter or

in a cupboard. It should never be operated

without the top trim.

• Leave at least 3 cm of space between

the side and rear walls of the product and

the walls of the counter/cupboard when

installing your product under a counter or in a

cupboard.

Mounting over a washing machine

• A fitting device should be used between

the two machines when installing above a

washing machine. The bracket (Part no. 297

720 0100 white/297 720 0400 grey) must be

installed by the Authorised Service Agent.

• Place the product on a firm floor. If it will be

placed on top of a washing machine, the

approximate weight of both machines may

reach 180 kg when they are full. Therefore,

the floor must be capable of carrying the load

on it!

Connection to water drain;

In products equipped with a condenser unit the

water accumulated during the drying cycle is

collected in the water tank. You should drain the

accumulated water after each washing cycle.

You can directly send the accumulated water

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blomberg TKF 8431 A Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info