Bedienungsanleitung Blomberg TKF 8439 S (Seite 5 von 44) (Deutsch, Englisch)

581567

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

2 Installation

Refer to the nearest Authorised Service

Agent for installation of your product.

C Preparation of location and electrical

installation for the product is under

customer’s responsibility.

BInstallation and electrical connections

must be carried out by a qualified

personnel.

A Prior to installation, visually check if the

product has any defects on it. If so, do

not have it installed. Damaged products

will cause risks for your safety.

Appropriate installation location

• Install the product in an environment

which has no risk of freezing and is in a

stable and level position.

• Operate your product in a well

ventilated, dust-free environment.

• Do not block the air ducts in front of

and under the product with materials

such as long pile rugs and wooden

bands.

• Do not place your product on a long

pile rug or on similar surfaces.

• Do not install the product behind a door

with a lock, sliding door or a hinged

door which can strike the product.

• Once the product is installed, it should

stay at the same place where its

connections have been made. When

installing the product, make sure

that the rear wall of it does not touch

anywhere (tap, socket, etc.) and also

pay attention to install the product at a

place where it will stay permanently.

B Do not place the product on top of the

power cable.

• Keep at least 1.5 cm distance to walls

of other furniture.

Under counter installation

• A special part (Part no. 297 360 0100)

replacing the top trim must be provided

and installed by the Authorised Service

Agent in order to use the machine

under a counter or in a cupboard. It

should never be operated without the

top trim.

• Leave at least 3 cm of space between

the side and rear walls of the product

and the walls of the counter/cupboard

when installing your product under a

counter or in a cupboard.

Mounting over a washing mac-

hine

• A fitting device should be used between

the two machines when installing above

a washing machine. The bracket must

be installed by the Authorised Service

Agent.

• Place the product on a firm floor. If

it will be placed on top of a washing

machine, the approximate weight of

both machines may reach 180 kg when

they are full. Therefore, the floor must be

capable of carrying the load on it!

Connection to water drain;

In products equipped with a condenser unit

the water accumulated during the drying

cycle is collected in the water tank. You

should drain the accumulated water after

each washing cycle.

You can directly send the accumulated

water out through the water drain hose

supplied with the machine instead of

periodically draining the water collected in

the water tank.

Connecting the water drain hose;

1. Remove the hose on the machine by

pulling it out from its end. Do not use

any tools to take out the hose.

2. Connect the special drain hose supplied

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blomberg TKF 8439 S Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blomberg TKF 8439 S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info