Bedienungsanleitung Blomberg WNF 7361 SCE20 (Seite 3 von 68) (Deutsch, Englisch, Italienisch)

582069

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Removing packaging reinforcement

Tilt the machine backwards to remove the packaging

reinforcement. Remove the packaging reinforcement by

pulling the ribbon.

Removing the transportation locks

 Donotremovethetransportationlocksbeforetaking

out the packaging reinforcement.

Remove the transportation safety bolts before operating

the washing machine, otherwise, the product will be

damaged.

1. Loosenalltheboltswithaspanneruntiltheyrotate

freely (C).

2. Remove transportation safety bolts by turning them

gently.

3. AttachtheplasticcoverssuppliedintheUserManual

bag into the holes on the rear panel. (P)

 Keepthetransportationsafetyboltsinasafeplaceto

reuse when the washing machine needs to be moved

again in the future.

Never move the product without the transportation

safety bolts properly fixed in place!

Connecting water supply

 Thewatersupplypressurerequiredtoruntheproduct

isbetween1to10bars(0.1–10MPa).Itisnecessary

tohave10–80litersofwaterflowingfromthefully

open tap in one minute to have your machine run

smoothly. Attach a pressure reducing valve if water

pressure is higher.

 Ifyouaregoingtousethedoublewater-inletproduct

asasingle(cold)water-inletunit,youmustinstallthe

supplied stopper to the hot water valve before operating

the product. (Applies for the products supplied with a

blind stopper group.)

 Ifyouwanttousebothwaterinletsoftheproduct,

connect the hot water hose after removing the stopper

and gasket group from the hot water valve. (Applies for

the products supplied with a blind stopper group.)

Models with a single water inlet should not be

connectedtothehotwatertap.Insuchacasethe

laundry will get damaged or the product will switch to

protection mode and will not operate.

 Donotuseoldorusedwaterinlethosesonthenew

product.Itmaycausestainsonyourlaundry.

1. Connectthespecialhosessuppliedwiththeproductto

thewaterinletsontheproduct.Redhose(left)(max.90

ºC)isforhotwaterinlet,bluehose(right)(max.25ºC)is

for cold water inlet.

Ensure that the cold and hot water connections are

made correctly when installing the product. Otherwise,

your laundry will come out hot at the end of the washing

process and wear out.

2. Tighten all hose nuts by hand. Never use a wrench

when tightening the nuts.

3. Open the taps completely after making the hose

connection to check for water leaks at the connection

points.Ifanyleaksoccur,turnoffthetapandremove

the nut. Retighten the nut carefully after checking the

seal. To prevent water leakages and damages caused

by them, keep the taps closed when the machine is not

in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectlyconnectedto

the wastewater drain or to the washbasin.

Your house will be flooded if the hose comes out of

its housing during water discharge. Moreover, there is

risk of scalding due to high washing temperatures! To

prevent such situations and to ensure smooth water

intake and discharge of the machine, fix the end of the

discharge hose tightly so that it cannot come out.

• Thehoseshouldbeattachedtoaheightofatleast40

cm,and100cmatmost.

• Incasethehoseiselevatedafterlayingitonthefloor

levelorclosetotheground(lessthan40cmabovethe

ground), water discharge becomes more difficult and

the laundry may come out excessively wet. Therefore,

follow the heights described in the figure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blomberg WNF 7361 SCE20 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info