Bedienungsanleitung Blomberg WNF 9447 ACE20 (Seite 3 von 70) (Englisch, Dänisch)

581988

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Removing the transportation locks

 Donotremovethetransportationlocksbefore

taking out the packaging reinforcement.

 Removethetransportationsafetyboltsbefore

operating the washing machine, otherwise, the

productwillbedamaged.

1. Loosenalltheboltswithaspanneruntilthey

rotate freely (C).

2. Removetransportationsafetyboltsbyturning

them gently.

3. AttachtheplasticcoverssuppliedintheUser

Manualbagintotheholesontherearpanel.(P)

 Keepthetransportationsafetyboltsinasafe

place to reuse when the washing machine needs

tobemovedagaininthefuture.

Never move the product without the

transportationsafetyboltsproperlyfixedinplace!

Connecting water supply

 Thewatersupplypressurerequiredtorunthe

productisbetween1to10bars(0.1–10MPa).

Itisnecessarytohave10–80litersofwater

flowing from the fully open tap in one minute

to have your machine run smoothly. Attach a

pressure reducing valve if water pressure is

higher.

 Ifyouaregoingtousethedoublewater-inlet

productasasingle(cold)water-inletunit,you

must install the supplied stopper to the hot water

valvebeforeoperatingtheproduct.(Applies

fortheproductssuppliedwithablindstopper

group.)

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

the hot water valve. (Applies for the products

suppliedwithablindstoppergroup.)

 Modelswithasinglewaterinletshouldnotbe

connectedtothehotwatertap.Insuchacase

the laundry will get damaged or the product will

switch to protection mode and will not operate.

 Donotuseoldorusedwaterinlethoseson

thenewproduct.Itmaycausestainsonyour

laundry.

1. Connectthespecialhosessuppliedwiththe

product to the water inlets on the product. Red

hose(left)(max.90ºC)isforhotwaterinlet,blue

hose(right)(max.25ºC)isforcoldwaterinlet.

Ensure that the cold and hot water connections

are made correctly when installing the product.

Otherwise,yourlaundrywillcomeouthotatthe

end of the washing process and wear out.

2. Tightenallhosenutsbyhand.Neverusea

wrench when tightening the nuts.

3. Openthetapscompletelyaftermakingthe

hose connection to check for water leaks at the

connectionpoints.Ifanyleaksoccur,turnoff

the tap and remove the nut. Retighten the nut

carefully after checking the seal. To prevent water

leakagesanddamagescausedbythem,keep

the taps closed when the machine is not in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

 Yourhousewillbefloodedifthehosecomesout

of its housing during water discharge. Moreover,

there is risk of scalding due to high washing

temperatures! To prevent such situations and to

ensure smooth water intake and discharge of the

machine, fix the end of the discharge hose tightly

so that it cannot come out.

• Thehoseshouldbeattachedtoaheightofat

least40cm,and100cmatmost.

• Incasethehoseiselevatedafterlayingitonthe

floorlevelorclosetotheground(lessthan40cm

abovetheground),waterdischargebecomes

more difficult and the laundry may come out

excessively wet. Therefore, follow the heights

describedinthefigure.

• Topreventflowingofdirtywaterbackintothe

machine and to allow for easy discharge, do

not immerse the hose end into the dirty water or

driveitinthedrainmorethan15cm.Ifitistoo

long, cut it short.

• Theendofthehoseshouldnotbebent,itshould

notbesteppedonandthehosemustnotbe

pinchedbetweenthedrainandthemachine.

• Ifthelengthofthehoseistooshort,useitby

addinganoriginalextensionhose.Lengthofthe

hosemaynotbelongerthan3.2m.Toavoid

waterleakfailures,theconnectionbetweenthe

extension hose and the drain hose of the product

mustbefittedwellwithanappropriateclampas

not to come off and leak.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blomberg WNF 9447 ACE20 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info