764934
12
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
12
EN POSITIONING AND CONNECTiNG THE DEVICE
Please Note!
The device must have clearance of at least 1 m above it and to all sides and be placed
on a dry, even, solid and moistureresistant surface.
Only connect the device to a plug socket that is properly installed and matches the
technical data of the device. The plug socket must also be readily accessible after
connection so that the connection to the mains can quickly be isolated.
1. Position the device at the location you want. When you do this, push the device
carefully so that the water in the water tank (10) does not spill out.
2. Secure the device to stop it rolling away by moving the castor lock (8) on the two front
castors (9) to the ON position.
3. Fully unwind the connecting cable and connect it to an easily accessible plug socket.
You will hear a beep. All elements on the control panel (2) will light up and go out with
the exception of the operating lamp POWER (25). The device is in standby mode.
USE
Please Note!
Do not use the device without water. The pump could be damaged.
Do not move the device during operation. Before the location of the device is changed,
switch off the device and disconnect it from the mains power.
Do not operate the device unsupervised so that you can intervene immediately if there
are any faults.
1. Fill the water tank (10) (see the “Filling the Water Tank” chapter).
2. Position the device at the location you want and connect it (see the “Positioning and
Connecting the Device” chapter).
3. Touch the POWER fi eld (25) to switch on the device. The device starts to operate on
speed level 1. The ionisation ION (18) and the cooling and humidifying function COOL
(24) are activated.
4. Adjust the settings of the device to suit your individual needs (see the “Functional
Overview of the Operating Elements” chapter).
5. If the device is no longer going to be used, switch off the device via the POWER fi eld
and pull the mains plug out of the plug socket.
The air flow can be increased or decreased. To do this, move one of the
side levers(15) on the ventilation grille (3) manually up or down. This will
adjust the horizontal slats of the ventilation grille.
2020-11-18 OCG BluMill Power Air Cooler - V07326 Manual V02.indd 122020-11-18 OCG BluMill Power Air Cooler - V07326 Manual V02.indd 12 03-12-2020 16:0003-12-2020 16:00
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Blumill Air Cooler KLP-B025 - V07326 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info