Bedienungsanleitung Blumill EP1069-GS - Ice cube machine (Seite 4 von 31) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

753386

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

6 7

EN EN

BEFORE FIRST USE

1. Please ensure the ice maker is level and on a stable table or platform to avoid

malfunction.

2. The incline angle of the ice maker cabinet should not exceed 45°during transportati-

on or use. Do not turn the ice maker upside down. Doing so could cause the com-

pressor or refrigerating system to operate incorrectly. Please allow time for the uids

in the compressor to settle after the ice maker is moved or transported. Before using

the ice maker for the rst time, please wait for 2 hours after the unit has been leveled

and positioned in the proper place.

3. Unpack the appliance, then check and make sure that all the accessories including

ice basket and ice scoop etc. are complete. Please contact with the client service

department if some accessories are missed.

4. The appliance must be placed on a dry and level surface with sucient ventilation,

far from heat sources such as ovens, heaters and corrosive gases.Leave an about

8-inch clearance on all sides of the ice maker for proper ventilation.

5. Do not ll the water reservoir with hot water. This may damage the ice maker. It isDo

not use the appliance at a very cold environment (lower than 50C).

6. Clean the appliance by following the operation of “CLEANING AND MAINTENANCE”

before operate.

USING YOUR ICE MAKER

1. Ensure that the drain plug at the bottom of water reservoir is closed well.

2. Plug the ice maker into the wall outlet, the “ICE” indicator blinks.

Note: Please make the ice maker be rested for 30 minutes before plug if it has been

moved.

3. Open the top lid and remove the ice basket.

4. Fill the water reservoir with drinking water.

Note: Do not ll above the MAX water level mark.

5. Replace the ice basket and close the top lid.

6. Press the ON/OFF key and the “ICE” indicator lights solidly.

7. The ice-making cycle will last approximately 7-15 minutes, depending on the ambient

temperature and water temperature.

8. The ice-making cycle starts with water being pumped into the ice tray situated below

the evaporator. Over the next 7-15 minutes ice forms on the evaporator. Once this

has completed, the ice tray will tilt backwards and the remaining water in the ice tray

is drained back into the water reservoir. The ice cubes are then dropped from the

evaporator and pushed forward into the ice basket by the ice shovel. The ice tray will

automatically move back into position under the evaporator and start the next cycle.

9. The “ICE FULL” indicator will light up when the ice basket is full and the ice maker will

stop the ice-making cycle automatically. Gently remove the ice from the ice basket

with the ice scoop. About 5 seconds later, the ice maker will restart its ice making

function automatically.

10. The “ADD WATER” indicator will light up when the water reservoir is lack of water

and the ice-making cycle will stop automatically. At that time, remove the ice basket

and add water to the water reservoir, and then press ON/OFF key again to restart the

ice-making cycle.

11. When you have got your desired amount of ice, stop the ice making cycle by pressing

the ON/OFF key and unplug the unit from the wall outlet.

12. Open the top lid and transfer the ice to a freezer.

Note: The ice will last in the ice maker for up to a 18 hour period, depending on the

ambient temperature.

13. Allow the ice maker to reach room temperature.

14. Suggest replacing the water every a week. Please empty the water reservoir if the ice

maker is not used for a long time.

CLEANING AND MAINTENANCE

Check and make sure the drain plug must be closed well. Fill the water reservoir with

clean water, then hold and press the“ON/OFF” key for 10 seconds, the pump will start to

pump water and keep running for 15 minutes, and it will enter into standby condition after

running for 15 minutes, nally, open the drain plug and empty the water

To keep your ice tasting fresh and your ice maker looking great, we recommend cleaning

your ice maker once per week.

1. Stop the ice-making cycle by pressing the ON/OFF key, unplug the ice maker from the

wall outlet and allow it to warm up to room temperature.

2. If residual water is found in the ice tray, gently push the ice tray back so that all water

drains into the water reservoir.

3. Move the appliance forward to a position 75mm away from the working table and

open the drain plug to drain out excess water (see Fig.3, Fig.4 and Fig.5).

4. Remove the ice basket.

5. Clean the evaporator by following the operation as below: pour the clean water into

the ice maker and run it to make ice for three cycles, and then empty the ice and

water in the ice maker.

6. Clean the ice maker interior with a soft cloth soaked with warm water and vinegar,

then rinse with clean water and then drain all the water.

7. Replace the drain plug well in position. Wash the ice basket and ice scoop in warm

soapy water. Rinse and dry.

8. Clean the exterior of the ice maker with a soft damp cloth. Use a mild dishwashing

soap, if necessary.

Note: Do not use organic solvent, boiled water, detergent, strong acid and strong

alkali etc. for cleaning.

9. Please empty the water reservoir and dry it for storage if the ice maker is not used for

a long time.

1 2 3

Blumill EP1069-GS - Ice cube machine Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info