Bedienungsanleitung BML Phoenix (Seite 5 von 6) (Englisch)

732396

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Left joystick

Climb

Descend

Turn

left

Turn

right

Step back

Step left

Right joystick

Backward

Forward

Move

left

Move

right

Step forward

Step right

SPECIAL FEATURES

Obstacle sensor

When the sensor detects an obstacle at a distance of 1 meter (depending on the envi-

ronment), the drone stops moving. The sensor is activated automatically 1 metre above

the ground. The sensor cannot prevent all crashes, so never fly too close to people and

animals.

1m 1m

CAUTION: Obstacle detection only works at low speeds and in good visibility. The sensor

cannot detect glass surfaces. Best results are achieved when detecting white walls. When

sensor is working, it is not possible to use headless mode or the return to starting point

button.

Maintaining height

When releasing the height control joystick, the drone remains hovering at the same height.

Flip

Climb to a height of at least 2 metres and press and hold the left joystick. Then move the

right joystick in any direction and the drone will flip up and over in that direction and back.

CAUTION: Flip does not work when the obstacle sensor is attached to the drone. After

removing it, you must restart the controller. Flip also does not function when the battery

is low.

Speed switch

By pressing the right joystick, you can choose between slow (one beep), medium (two

beeps), and high (three beeps) speed.

Return to start point

Press the button and the drone will fly back to its starting position. With the right joys-

tick, you can control the flight back to the left or right. Move the right joystick up to abort.

Only use the return function in the open air and when the air is calm. It cannot be guaran-

teed that this feature will return the drone to the exact same position as it depends on the

surrounding conditions. Therefore, when flying, keep the drone under control and under

supervision so you can safely land it. Using the return function does not exclude you from

damage or injury liability.

Headless mode

Turning on

After pairing the drone with the controller, press the headless mode button. The controller

beeps and the LEDs on the drone blink.

Turning off

When the drone is in headless mode, press the headless mode button. The controller then

beeps and the LEDs light up.

Setting forward direction

Before turning on headless mode, you

need to set the direction forward. Point the

drone so that it is facing the same direc-

tion as you (1). Then move both joysticks

to the left and hold them in this position

for 2 seconds (2). The LEDs on the drone

will flash.

Controls in headless mode

In headless mode, the forward direction is

always the direction that has been pre-set.

Always stand facing this direction during

operation. In headless mode, it does not

matter which direction you turn the drone

– when moving the right joystick forward,

it always flies away from you, even if it is

facing sideways.

1 2

TIPS:

1. The simplest way to fly in headless mode is to carefully set the forward direction and

after take-off to make sure you stand facing this direction and not to move.

2. If the drone moves differently than it should, abort the flight and set it up again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BML Phoenix Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info