Bedienungsanleitung BMW 1 serie - 2013 (Seite 117 von 288) (Englisch)

618771

117

Zoom out

Zoom in

Vorherige Seite

1/288

Nächste Seite

112

Controls Practical interior accessories

3. Hold the hand-held transmitter of the

device to be controlled about 1 in/2.5 cm to

3 in/8 cm away from the buttons on the

inside mirror.

The required distance depends on the

hand-held transmitter.

4. Simultaneously press and hold the button

of the desired function on the hand-held

transmitter and the button to be pro-

grammed on the inside mirror.

The LED on the inside mirror will flash

slowly at first.

5. As soon as the LED flashes rapidly, release

both buttons. The rapid flashing indicates

that the button on the inside mirror has

been programmed.

If the LED does not flash rapidly within

60 seconds, change the distance between

the inside mirror and the hand-held trans-

mitter and repeat this step. This may

require several attempts. Allow at least

15 seconds between attempts.

6. To program additional functions on the

other buttons of the inside mirror, repeat

steps 3 through 5.

The buttons on the inside mirror can be used to

operate the devices if the ignition is switched

on.

Special procedure with alternating-

code systems

If the device fails to function even after repeated

programming, check whether the device to be

controlled uses an alternating-code system.

To do so, either read the instructions for the

device or hold down the programmed button on

the inside mirror. If the LED on the inside mirror

flashes quickly at first and then remains lit for

2 seconds, the device uses an alternating-code

system. The LED flashes and lights up repeat-

edly for approx. 20 seconds.

In devices with an alternating-code system, the

Integrated universal remote control and the

device must also be synchronized.

For information about synchronizing can also

be found in the operating instructions for the

device to be set.

Programming will be easier with the aid of a

second person.

Synchronizing:

1. Park your vehicle within the range of the

remote-controlled device.

2. Program the Integrated universal remote

control as described above.

3. Locate and press the synchronization

button on the device to be set. You have

approx. 30 seconds to perform the next

step.

4. Hold down the programmed button on the

inside mirror for approx. 3 seconds and then

release it. Repeat this operation, up to three

times if necessary, to complete the syn-

chronization. If the synchronization has

succeeded, the programmed function is

performed.

Reprogramming individual buttons

1. Switch on the ignition.

2. Hold the hand-held transmitter of the

device to be controlled about 1 in/2.5 cm to

3 in/8 cm away from the buttons on the

inside mirror.

The required distance depends on the

hand-held transmitter.

3. Press the desired button on the inside

mirror.

4. If the LED on the inside mirror flashes

slowly after approx. 20 seconds, press the

transmit key of the hand-held transmitter.

5. As soon as the LED flashes rapidly, release

both buttons.

If the LED does not flash rapidly after

approx. 60 seconds, alter the distance and

repeat the step.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BMW 1 serie - 2013 Seite 117

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info