Bedienungsanleitung BMW 335is - 2010 (Seite 107 von 200) (Englisch)

618889

107

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Reference At a glanceControlsDriving tipsMobility

105

The corresponding memory button 1 is now

programmed with the signal of the original

hand-held transmitter.

You can operate the device while the ignition is

switched on.

If the device fails to function even after

repeated programming, check whether

the original hand-held transmitter uses an alter-

nating-code system. To do so, either read the

instructions for the original hand-held transmit-

ter or hold down the programmed memory

button 1 of the integrated universal remote

control. If the LED 2 on the integrated universal

remote control flashes rapidly and then remains

lit for about two seconds, the original hand-held

transmitter uses an alternating-code system. If

it uses an alternating-code system, program

the memory buttons 1 as described under

Alternating-code hand-held transmitters.<

Alternating-code hand-held

transmitters

To program the integrated universal remote

control, consult the operating instructions for

the device to be set. You will find information

there on the possibilities for synchronization.

When programming hand-held transmitters

that employ an alternating code, please observe

the following supplementary instructions:

Programming will be easier with the aid of

a second person.<

1. Park your vehicle within the range of the

remote-controlled device.

2. Program the integrated universal remote

control as described above in the section

Fixed-code hand-held transmitters.

3. Locate the button on the receiver of the

device to be set, e.g. on the drive unit.

4. Press the button on the receiver of the

device to be set. After step 4, you have

approx. 30 seconds for step 5.

5. Press the programmed memory button 1 of

the integrated universal remote control

three times.

The corresponding memory button 1 is now

programmed with the signal of the original

hand-held transmitter.

If you have any questions, please contact

your BMW center.<

Deleting all stored programs

Press the left and right memory buttons 1 for

approx. 20 seconds until the LED 2 flashes rap-

idly: all stored programs are deleted.

Reassigning individual programs

1. Hold the original hand-held transmitter at a

distance of approx. 4 to 12 in/10 to 30 cm

from the memory buttons 1.

The required distance between the

hand-held transmitter and the mem-

ory buttons 1 depends on the system of the

respective original hand-held transmitter

used.<

2. Press the desired memory button 1 of the

integrated universal remote control.

3. If the LED 2 flashes slowly after approx.

20 seconds, press the transmit key of the

original hand-held transmitter. Release

both buttons as soon as the LED 2 flashes

rapidly. If the LED 2 does not flash rapidly

after approx. 15 seconds, alter the distance

and repeat this step.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BMW 335is - 2010 Seite 107

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info