HOW TO REMOVE YOUR CHILD SEAT FROM A LUGAGGE CARRIER
ASSEMBLY INSTRUCTIONS
EXCLUSIVE MAXI & TOUR PLUS FRAME
HOW TO ASSEMBLE YOUR CHILD SEAT ON A BICYCLE FRAME
1. Open the buckle(C1) and detach the safety-belt (C) in order to remove the child bicycle seat.
2. Press the jaws (I) and pull both of them out. At the same time, pull the child seat up and back.
1. Access the front cover of the child seat (E) and remove the key (N).
2. Remove the metallic bracket (K) from the metallic support bar (L). To do
that, you should press the metallic bracket button (K3) and simultaneously
pull the metallic support bar (L) up.
3. Remove the screws (K1) on the Metallic bracket (K), with the Allen key
No. 5 (N).
4. The correct positioning of the metallic bracket (K) is extremely
important. Make sure the metallic bracket (K) is positioned in the frame
according to the picture. Place the body of the front mounting block (K2)
on the bicycle frame from the front. Insert 4 screws (K1) in the block to
tighten the rear metallic mounting plate (K4), so that the hight can be
adjusted later.
5. Tighten the screws, with the Key (N), so that the metalic bracket (K) is
secured but not fully tightened so that, if necessary, you can adjust the
height later. However, note that it should be tight to make it easier to
complete the next step. You need to tighten the 4 screws diagonally and
in stages. Check the safety of the fasteners regularly.
6. Place the edges of the metallic support bar (L) at the holes of the metallic
bracket (K) until you hear a click indicating the lock, and until the centre
button (K3) shall be level with the exterior of the hose metallic bracket.
7. Centre and adjust the metallic bracket (K) at a height above the rear
wheel, so that later, when you add the weight of the child, the child bicycle
seat does not touch the wheel. Note that the metallic bracket (K) should
be positioned at a maximum of 10cm away from the wheel. Never use
the metallic support bar (L) to carry other loads than this child seat, as
indicated in this manual.
8. To install the metallic support bar (L) on the child seat (A) you need to
first clamp the frontal clamping point (L1) on the Safety Metallic Device (J).
9. Then, clip the Metallic support bar lateral clamping points (L2) on the
opening and clamping jaw (I) of the child seat (A). Make sure that you will
hear a click when the clamping is done, this is extremely important for you
and your child safety.
10. The child seat has a center of gravity (F) (engraved on the child seat)
that must be positioned in front of the rear wheel axle. If it is positioned
behind the axle, the distance must not exceed 10 cm. Special care must
also be taken when positioning the child seat to ensure that the cyclist
does not touch the child seat with his feet when cycling.
Note: In Germany, according to the German Traffic Law StVZO, bicycle seats
may only be fixed so that 2/3 of the seat depth or the Gravity Center of the
seat is located between the front and rear axle of the bicycle.
11. After adjusting the height and positioning of the seat, hand tighten the
Metallic bracket (K) to ensure that it cannot move. This tightening must
be manual and is extremely important for the safety of the child. Make
sure that the Metallic bracket (K) is firmly attached. You need to hand tight
the 4 screws (K1) diagonally, with the same force and in stages, with a
recomended torque of 8 N.m.
12. Start to open the safety belt buckle (C1) and pass it around the bicycle
frame. Adjust the belt it as shown in the picture, under tension.
13. Make sure that remain loosen belt is not in contact with the wheel,
so pass it trought the Safety belt retainer (C2). This step is extremely
important for the child’s safety.
14. Make sure you have followed and fulfilled all the instructions given.
When done so, the child bicycle seat is ready for use. IT IS MANDATORY
TO READ the following chapter on safety instructions about using
your child bicycle seat.
1. Open the buckle (C1) and detach the safety-belt (C) in order to remove the child bicycle seat.
2. If you want to remove the full system, press the block button (K3) of the Metallic Bracket (K) and simultaneously pull the metallic Support bar (L) and
the seat up and back as shown in the image.
3. If you wish to keep the metallic support bar (L) and only remove the seat, press the jaws (I) and pull both of them out. At the same time, pull the child
seat up and back.
ASSEMBLY INSTRUCTIONS
EXCLUSIVE MAXI & TOUR PLUS FRAME
HOW TO REMOVE YOUR CHILD SEAT FROM A BICYCLE FRAME
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Bobike Exclusive Maxi Plus wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
