Bedienungsanleitung Bomann BS 9018 (Seite 32 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

687992

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

NOTE:

If the red mark is visible, pull in the cable with the help of

the cable winding button back to the yellow mark.

2. Insert the mains plug into a correctly installed power socket.

3. Turn the device on by the on/off switch by pressing down

the button.

4. Set the “carpet/hard oor” switch, depending on the oor

covering.

5. Vacuum at a steady speed. There is no need to exert pres-

sure.

NOTE:

Pay attention to the range that can be covered with the

cable length!

Air Slide (15)

Open the air slide on the hose handle in order to regulate the

airow or to clear any particles sticking to the nozzle.

Switching off and Winding up the Mains Lead

1. Turn the vacuum cleaner off by the on/off switch and

remove the plug from the socket.

2. Keep the plug in your hand.

3. Press the cable winding button and guide the cable. Hold

the cable to avoid wrapping.

Maintenance

Emptying the Dust Collector

Empty the dust collector once the collected dirt reaches the

MAX marking.

1. Disconnect the mains plug from the wall socket.

2. Press the button (10) to

release the dust collector.

Remove the dust collector.

3. Empty the dust collector

over a dustbin. In order to

do so, press the button on

the dust collector to open

the base plate.

4. Then close the base plate again.

5. Attach the dust collector to the appliance. It must engage

with a click.

Filter

Your appliance features 4 lters. The common dust bag system

has been replaced by a transparent dust collector. The higher

ow speed of the collector allows for heavy dirt and smallest

oating particles to be separated from the “sucked-in air”.

It is thus not necessary to buy dust bags.

HEPA Filter

Clean the lter element twice a year.

CAUTION:

• Never wash the lter in the washing machine.

• Do not use a hairdryer for drying.

• Only use the appliance after the lters have been

installed correctly.

Proceed as follows to remove, clean and reinstall the lter ele-

ment:

1. Empty the dust collector as described previously.

2. Remove the dust collector lid. To do so, turn the ↓ marking

on the lid towards the

symbol. Pull the lter element from

the dust collector.

3. Remove the lter element from the lid by turning the lter

element towards OPEN.

4. Pull the nylon lter from the HEPA.

5. Use a brush to clean the

lters. In case of heavy

staining, clean the lters

under running water.

6. Let the lters air-dry

completely before retting

them!

7. Wipe the dust collector with a damp cloth and then wipe it

dry.

8. Once the lters are com-

pletely dry, attach the nylon

lter to the HEPA lter.

9. Reinsert the lter element

into the lid of the dust

collector, using the notches

in the lid. Turn the lter ele-

ment towards the CLOSE

symbol.

10. Reinsert the lid including the lter element into the dust

collector. Close the lid until the ↓ marking is aligned with

the symbol.

11. Fit the dust collector in the appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann BS 9018 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info