Bedienungsanleitung Bomann bz 9482 cb (Seite 16 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

364279

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Dismantling beer dispenser

To clean the beer dispenser and/or to replace the keg,

it is necessary to remove the dispensing unit from the

dispenser. The procedure for this is as follows:

1. When the installed keg is empty,

ﬁ rst remove the CO2 cartridge

from the CO2 chamber by opening

the same and unscrewing the CO2

cartridge holder.

CAUTION FROSTBITE:

• A residual amount of CO2 may still be present in

the cartridge, which suddenly empties and results

in the formation of ice.

NOTE

• It is recommended to initially ﬁ t the CO2 cartridge

when preparing the next keg so that the cartridge

cannot accidentally empty if the dispenser lid is

closed without a 5 litre party keg being present in

the dispenser.

2. Press the lid opener.

3. Detach the end of the dispensing

unit from the CO2 feed valve and

remove the keg together with the

dispensing unit using the handle

provided.

NOTE

• The silicon sealing ring for the

CO2 feed valve is a wearing

part. If excessive CO2 losses

are noticed during use, replace

the silicon sealing ring with the

supplied spare seal.

Remove the clamps from the rim of the

keg and pull the dispensing unit out of

the keg quickly and evenly. As the beer

tap may not be moist during extraction,

removal may take some effort.

The dispensing unit can now be

cleaned as described in the chapter

"Cleaning" and subsequently installed

on a new keg as described in the

chapter "Preparations".

ATTENTION!

Never remove the dispensing unit from the keg when

pressurised. To change the keg before it is empty,

remove the keg together with the dispensing unit from

the dispenser. Position it in such a way that the beer is

able to ﬂ ow out into a suitable container and pull the tap

handle until no more beer is dispensed.

Cleaning

In order to keep the quality of the dispensed beer at

a consistently high level, it is important to clean the

dispenser thoroughly. The cleaning intervals are speciﬁ ed

in the following.

ATTENTION!

Never use scouring pads, aggressive scouring agents,

acetone, benzine, acids, thinner, vinegar or similar for

cleaning purposes.

Cleaning after each use

Both the collecting tray and drip tray

should be cleaned after each use

of the dispenser to ensure perfect

hygiene.

For this purpose, remove both the

collecting tray and drip tray from the

dispenser and pour the collected beer

into the drain. Subsequently clean

both parts with hot water, using a

small amount of washing/up liquid if

necessary.

ATTENTION!

The parts are not dishwasher proof.

It is recommended to also clean the tube at the front of

the beer tap after each use.

For this purpose, remove the cover at

the front below the beer tap and

remove the tube. Subsequently rinse

out the tube with warm water.

ATTENTION!

If no beer is dispensed over

several days, it is recommended

to thoroughly clean the tube. The

supplied cleaning balloon should be

used for this purpose as follows:

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann bz 9482 cb Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann bz 9482 cb

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info