Bedienungsanleitung Bomann cb 2002 (Seite 23 von 54) (Deutsch, Englisch, Holländisch, Italienisch)

361458

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

ENGLISH

Cleaning the Brew Group

Before cleaning the device switch it to the „O“

position and then remove the mains plug (19) from

the socket.

If the machine is used daily the brew group must be

cleaned regularly, i.e. at least once a week. Only warm

water should be used for cleaning.

• Allow the machine to cool down.

• Open the service door (6).

• Lift the brew group slightly and then carefully pull it

out horizontally.

• Rinse the brew group thoroughly with warm water.

• Allow the brew group to dry.

• Clean the service chamber with a damp cloth.

• Reinstall the brew group horizontally until it locks in

place.

• Close the service door.

Note: Only if the service door can be closed easily is

the brew group correctly in position.

Removing/Inserting the Brew Group

In order to remove the brew group please switch the

machine off and open the service door (6). Grip the brew

group by the handle (diagram A). Lift the brew group

slightly and then remove it from the housing. To reinsert

the brew group proceed in the reverse order (diagram B).

Cleaning the Filter Screens

Cleaning the Lower Filter Screen

If after a certain time the

coffee comes out of the

machine too slowly, or if

no coffee comes out, this

may be due to the fact

that the coffee that has

been used is too rich. In

this case you should open

the service door (6) and

remove the brew group. In diagram A the lower screen

is clearly visible. The brush of the measuring spoon can

be used to clean the screen. Any residues adhering to

the screen can be removed by gently moving the brush.

If the openings in the screen are still blocked you can

remove the screen from its retaining device. In order to

remove the screen please proceed as follows:

• Release the screw of the screen with an appropriate

cool.

• Remove the screen from its retaining mechanism.

• Hold the ﬁ lter up to the light and check which ﬁ lter

openings are blocked. Clean the openings with the

point of a needle if necessary.

• Now replace the cleaned screen in its retaining me-

chanism.

• Reposition the screw and gently tighten it.

Cleaning the Upper Filter Screen

The upper screen

becomes visible when

the brew group is rotated

- see diagram B. In order

to clean the screen please

proceed as described

above. Please note that

the upper screen is slight-

ly offset and its removal

requires a little dexterity.

Adjusting the Position of the Drive Shaft

If it is not possible to close the service door (6), check

whether the brew group has been correctly reinstalled.

Note: the drive shaft of the brew group must ﬁ t onto the

drive shaft of the motor. Should this not be the case,

please proceed as follows:

1. Turn the machine off by the I/O switch (5). Open the

service door (6).

2. Remove the brew group from the service chamber

and close the service door. Turn the machine on with

the I/O switch.

3. The drive shaft is now readjusted. This procedure

lasts approximately 20 seconds.

4. Then open the service door and try to insert the brew

group again.

Brew Group Underside

Spindle Coupling

Adjustment Tool

Spindle Coupling

05-KAV 2936 GB 23 03.12.2004, 12:13:30 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann cb 2002 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info