Bedienungsanleitung Bomann DTE 338 (Seite 20 von 28) (Deutsch, Englisch)

652039

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Install the power cord so that the appli-

ance can be easily connected after

installation.

Cut the sealing tape in accordance with

the built-in opening.

Stick the sealing tape succinct on the

appliance side to which the door

opens. Insert the appliance into the

built-in opening until the stop plate (A)

abuts the furniture.

Make sure that the stop plate lines up

properly with the top of the built-in

opening.

Screw the appliance door with the furniture door

Screw the appliance door with the furniture doorScrew the appliance door with the furniture door

Screw the appliance door with the furniture door

NOTE

NOTENOTE

NOTE:

Follow below instruction for connecting the furniture

door with the freezer and fridge appliance door.

First remove the caps of the bores on the outer edg-

es of the appliance doors.

Thereon the sliding hinge brackets have to be fixed.

Separate the parts b, c and d of part a.

In consideration of the shown distanc-

es, and in accordance with the appro-

priate door holes, hold the guide (a) at

the inside of the furniture door and

mark the positions of the drill holes.

After drilling, fix the guide with the

screws provided.

Insert the cover (c) until it clicks in the

guide (a).

Fully open the appliance and furniture

door and join them together. Slide the

bracket (b) in the guide (a) and mark

the drill holes. Remove the bracket and

drill Ø 2 mm holes with about 8 mm

distance to the outer door edge. Put the

bracket on again; secure it with the

screws provided.

If an aligning of the furniture door is

necessary, use the slot spacing. Check

if the door is arranged vertical as well

as horizontal, so that a smooth opening

and closing of the door is ensured.

Insert the cover (d) until it clicks on the

angle (b).

Fasten the appliance in the

Fasten the appliance in theFasten the appliance in the

Fasten the appliance in the

built

builtbuilt

built-

-in

inin

opening

openingopening

opening

Use the two supplied security angles to stabilize the

appliance. Attach the angles between the two doors on

the appliance and on the side of the furniture. Fix the

angle of the hinge-side in combination with the hinge.

Adjust the proper position of the angles by sliding them

in the screw-openings to the right/left until they meet the

sides of the built-in furniture.

Startup / Operation

Startup / OperationStartup / Operation

Startup / Operation

Prior to fi

Prior to fiPrior to fi

Prior to first use

rst userst use

rst use

CAUTION

CAUTIONCAUTION

CAUTION:

After transport, the appliance should be left standing

upright for about 4 hours before connecting to the

power supply. Nonobservance could lead to malfunc-

tion of the cooling system and causes an appliance

breakdown.

Clean the appliance interior including all accessory

parts. Consider the instructions which we provide in

the chapter “Cleaning and Maintenance”.

Starting the appliance

Starting the applianceStarting the appliance

Starting the appliance

• Connect the appliance to the power supply.

• Operate the temperature control. See also the

following section "Settings".

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann DTE 338 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info