Bedienungsanleitung Bomann DU 658 G (Seite 20 von 28) (Deutsch, Englisch)

651976

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

• Place the outer duct with the

fixed

parallel to the other rails (1+2).

•

Slide the inner (upper) duct along the slide fixture into the outer (lower) duct. Make sure that the inner duct

is aligned with the vents at the top.

duct or sliding back into the outer duct.

•

For extraction mode, correctly position the flexible

• Pull the inner duct cover up a

screwing in the plate screws (8)

(Fig. G)

Installing the activated carbo

nstalling the activated carbonstalling the activated carbo

nstalling the activated carbo

n filter for recirculation mode

n filter for recirculation moden filter for recirculation mode

n filter for recirculation mode

• Remove the alumin

um grease filter.

•

Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the

extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise until it

clicks into place.

• Reinstall the alumin

um grease filter

NOTE

NOTENOTE

NOTE:

The activated carbon filter absorbs

odours

Electrical connection

Electrical connectionElectrical connection

Electrical connection

WARNING:

WARNING:WARNING:

WARNING:

•

The installation to the mains supply must conform to the local standards

•

Improper connection may cause to an

• Do not modify the appliance

plug

an authorized specialist.

•

The accessibility of the power plug must be ens

supply in case of an emergency.

•

Ensure that your mains power corresponds with the specifications of the appliance. The specifications are

printed on the rating label.

• Connect the mains cable to a

properly installed and earthed wall outlet.

The

extractor hood is operated via pushbuttons.

switched on and off with the

corresponding

Lowest fan setting

Moderate fan setting

fixed

rail (3) onto the extr

actor hood (Fig. F). Fasten the rail (3) to the wall

Slide the inner (upper) duct along the slide fixture into the outer (lower) duct. Make sure that the inner duct

is aligned with the vents at the top.

Determine the exte

nsion length of the duct cover by pulling up the inner

duct or sliding back into the outer duct.

For extraction mode, correctly position the flexible

extraction hose (not supplied).

fasten the duct unit on the side to the

previously

(Fig. G)

n filter for recirculation mode

n filter for recirculation moden filter for recirculation mode

n filter for recirculation mode

um grease filter.

Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the

extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise until it

um grease filter

odours

and must be replaced at least every six

months

The installation to the mains supply must conform to the local standards

and regulations.

Improper connection may cause to an

electric shoc

electric shocelectric shoc

electric shock!

k!k!

plug

. If the plug does not fit properly to the outlet, let install a proper outlet by

The accessibility of the power plug must be ens

ured in order to disconnect the

appliance

Ensure that your mains power corresponds with the specifications of the appliance. The specifications are

properly installed and earthed wall outlet.

Startup / Operation

Startup / OperationStartup / Operation

Startup / Operation

extractor hood is operated via pushbuttons.

The individual fan settings as

well

corresponding

buttons.

Highest fan setting

Lighting

actor hood (Fig. F). Fasten the rail (3) to the wall

Slide the inner (upper) duct along the slide fixture into the outer (lower) duct. Make sure that the inner duct

nsion length of the duct cover by pulling up the inner

previously

mounted rail (2) by

Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the

extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise until it

months

regardless of use.

and regulations.

. If the plug does not fit properly to the outlet, let install a proper outlet by

appliance

from the power

Ensure that your mains power corresponds with the specifications of the appliance. The specifications are

well

as the lighting can be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann DU 658 G Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info