Bedienungsanleitung Bomann DU 660 IX (Seite 19 von 28) (Deutsch, Englisch)

651968

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

•

The hood is mounted below a suitable wall unit. Determine the position of the extractor hood centrally

above the hob in

conformance with the specified safety distances.

• Pull the pull-out device and re

move

• Hold the hood to the specified

cabinet

sponding to the six screw holes.

Check

• For extraction mode, you must

also

• If the mains cable is fed through

the

• Drill six mounting holes of

Ø 4 mm

• Screw in the appli

ance with the screws (1)

• Insert the connecting piece with

non

the mounting hooks on the

connecting piece

• For extraction mode, a flexible

extraction

fitted and connected to the

outside

• To fill the gap between the wall

and

depending on the gap. Mount the

• Reinstall the aluminum grease

filter.

Installing the activated carbo

nstalling the activated carbonstalling the activated carbo

nstalling the activated carbo

n filter for recirculation mode

n filter for recirculation moden filter for recirculation mode

n filter for recirculation mode

• Pull the pull-out device and r

emove the aluminum grease filter.

•

Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the

extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise u

clicks into place.

• Reinstall the alumin

um grease filter

NOTE

NOTENOTE

NOTE:

The activated carbon filter absorbs

odours

2 3

The hood is mounted below a suitable wall unit. Determine the position of the extractor hood centrally

conformance with the specified safety distances.

move

the aluminum grease filter.

cabinet

position and draw the drilling points from

the

Check

them with a spirit level.

also

create a feed through of approx. Ø 130 mm in

the

unit, a feed through also must be provided.

Ø 4 mm

through the base of the unit.

ance with the screws (1)

and washers under the wall unit.

non

-return valves (2) onto the extraction duct

from

connecting piece

latch into place.

extraction

hose (not supplied) with an inner

diameter

outside

by an extraction vent.

and

the appliance, attach the spacer strip

(3) on t

strip using the screws (4) in the holes provided

filter.

n filter for recirculation mode

n filter for recirculation moden filter for recirculation mode

n filter for recirculation mode

emove the aluminum grease filter.

Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the

extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise u

um grease filter

odours

and must be replaced at least every six

months

The hood is mounted below a suitable wall unit. Determine the position of the extractor hood centrally

the

inside of the unit corre-

the base of the unit.

from

above. Make sure that

diameter

of Ø 120 mm must be

(3) on t

he narrow or wide side,

the appliance.

Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the

extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise u

ntil it

months

regardless of use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann DU 660 IX Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info