Bedienungsanleitung Bomann DU 7602 G (Seite 19 von 28) (Deutsch, Englisch)

687866

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

•

Determine the position of the cooker hood central-

ly above the cooking area in accordance with the

specified safety distances.

• Mark the holes required for wall mounting as

shown in the drawing.

Specify in advance the extension length of the

shaft cover for the position of the bracket [04] at

the upper shaft end.

First, check the markings with a water balance.

• Drill totally 7x mounting holes for fixing the brack-

ets and two more holes for the hood body of ap-

prox. 8 mm diameter into the wall. Insert the en-

closed dowels [08].

• Fix the hood body bracket [05] with three screws

ST4x30mm [09] and the brackets [03] and [04] at

the pre-marked positions, each with two screws

ST4x30mm [09].

• Before inserting the hood, affix the non-return

valves [07] by gently bending them from above

onto the exhaust duct.

For exhaust mode:

For exhaust mode:For exhaust mode:

For exhaust mode:

Hereupon a flexible exhaust hose

(included in delivery) with 150 mm inner diameter

must be attached.

• Hang up the hood body onto the bracket [05].

Check the safe, horizontal support and tighten two

screws ST4x30mm [09] through the hood body.

For exhaust mode:

For exhaust mode:For exhaust mode:

For exhaust mode:

Check the correct position of the

exhaust hose and connect it with the outlet opening.

• Put the shaft unit on and secure the lower shaft

with the bracket [03].

• Pull up the inner shaft and fix the shaft cover

sideways with the bracket [04] by screwing in the

screws ST3x10mm [10].

Installing the activated carb

Installing the activated carbInstalling the activated carb

Installing the activated carbon

onon

filter for recirculation

filter for recirculation filter for recirculation

filter for recirculation

mode

modemode

mode

• Remove the aluminum grease filter (see “Clean-

ing the aluminum grease filter).

• Place the carbon filter onto the air intake of the

extraction duct. Make sure that the mounting pins

on the extraction duct engage the mounting slots

of the carbon filter. Turn the filter clockwise until it

clicks into place.

• Reinstall the aluminum grease filter.

Electrical connection

Electrical connectionElectrical connection

Electrical connection

WARNING:

WARNING:WARNING:

WARNING:

• The installation to the mains supply must conform

to the local standards and regulations.

• Improper connection may cause to an electric

electric electric

electric

shock

shockshock

shock!

• Do not modify the appliance plug. If the plug does

not fit properly to the outlet, let install a proper

outlet by an authorized specialist.

• The accessibility of the power plug must be en-

sured to disconnect the appliance from the power

supply in case of emergency.

• Ensure that your mains power corresponds with

the specifications of the appliance. The specifica-

tions are printed on the rating label.

• Connect the mains cable to a properly installed

and earthed wall outlet.

• If the plug after installation is not accessible, a

corresponding disconnect device must be availa-

ble to meet the relevant safety regulations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann DU 7602 G Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info