Bedienungsanleitung Bomann DU 7603G (Seite 20 von 28) (Deutsch, Englisch)

714359

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Fig. 2

Fig. 2Fig. 2

Fig. 2

Fig. 2a

Fig. 2aFig. 2a

Fig. 2a

• Before attaching the housing, insert the two non-

return valves by lightly bending them from above

into the connecting piece (extraction duct)

(Fig.

(Fig.(Fig.

(Fig.

2)2)

For the

For the For the

For the extraction mode

extraction modeextraction mode

extraction mode:

: :

Hereupon a flexible exhaust

hose (supplied) with an inner diameter of 150 mm

must be attached. Secure the hose with the enclosed

cable tie

(Fig. 2a)

(Fig. 2a)(Fig. 2a)

(Fig. 2a)

Fig.

Fig.Fig.

Fig.

Fig.Fig.

Fig.

• Hang up the housing. Check the secure hold and

the horizontal position. To secure the housing (D)

(D)(D)

(D),

screw in the lower screws 2x ST4*30mm through

the housing

(Fig. 3)

(Fig. 3)(Fig. 3)

(Fig. 3)

• Fix the bracket (with angle) for the upper shaft

closure (A)

(A)(A)

(A) with the screws 2x ST4*40mm after

determining the extension length of the shaft cov-

(Fig. 4)

(Fig. 4)(Fig. 4)

(Fig. 4)

For the

For the For the

For the extraction mode

extraction modeextraction mode

extraction mode:

: :

Check the correct position

of the exhaust hose and connect it with the outlet

opening.

Fig.

Fig.Fig.

Fig.

Fig.Fig.

Fig.

• Fasten the outer (lower) shaft with the bracket

(without angle) using the 2x ST4*8mm self-

tapping screws

(

((

(Fig.

Fig.Fig.

Fig.

5)5)

• Put on the telescoped shaft unit; fix the shaft unit

laterally to the housing with the self-tapping

screws 2x ST4*8mm and fix the middle shaft

bracket (B)

(B)(B)

(B) with the screws 2x ST4*40mm

(Fig. 6)

(Fig. 6)(Fig. 6)

(Fig. 6)

Fig.

Fig.Fig.

Fig.

• Pull up the inner shaft and fix the shaft cover lat-

erally to the shaft closure bracket using the self-

tapping screws 2x ST4*8mm

(Fig. 7)

(Fig. 7)(Fig. 7)

(Fig. 7)

Installing the activated carbon

Installing the activated carbonInstalling the activated carbon

Installing the activated carbon

filter for reci

filter for recifilter for reci

filter for recirculation

rculation rculation

rculation

mode

modemode

mode

• Remove the aluminum grease filter (see “Clean-

ing the aluminum grease filter).

•

Place the carbon filter onto the air

intake of the extraction duct.

Make sure that the mounting pins

on the extraction duct engage the mounting slots

of the carbon filter. Turn the filter clockwise until it

clicks into place.

• Reinstall the aluminum grease filter.

Electric

ElectricElectric

Electrical c

al cal c

al connection

onnectiononnection

onnection

WARNING:

WARNING:WARNING:

WARNING:

• The installation to the mains supply must conform

to the local standards and regulations.

• Improper connection may cause to an electric

electric electric

electric

shock

shockshock

shock!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann DU 7603G Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info