Bedienungsanleitung Bomann DU 771.1 G (Seite 19 von 28) (Deutsch, Englisch)

688078

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

• For mounting the hood drill in total 8x mounting

holes with approx. 8 mm diameter into the wall.

Insert the supplied dowels

(Fig. 1)

(Fig. 1)(Fig. 1)

(Fig. 1)

• Screw in the screws 2x ST4*40 for the hood body

so far that they project approx. 4 mm out of the

wall.

• Before inserting the hood, affix the connection

piece with the non-return valves from the top of

the extraction duct.

For exhaust mode (Fig.

For exhaust mode (Fig. For exhaust mode (Fig.

For exhaust mode (Fig. 2):

2):2):

2):

• Hereupon a flexible exhaust hose (not supplied)

with an inner diameter of 150 mm must be at-

tached.

• Hang up the hood body. Check the secure hold

and the horizontal position. Tighten the screws

through the hood body.

• Additionally secure the housing with the screws

2x ST4*30

(Fig. 2)

(Fig. 2)(Fig. 2)

(Fig. 2)

• Fix the bracket (with angle) for the upper shaft

termination with the screws 2x ST4*40

(F(F

(Fig.

ig.ig.

ig.

3)3)

• Fasten the outer (lower) shaft with the bracket

(without angle) using the metal screws 2x ST4*8

(Fig. 4).

(Fig. 4).(Fig. 4).

(Fig. 4).

• Put the shaft unit on and fasten the shaft bracket

with the screws 2x ST4*40

(F(F

(Fig.

ig.ig.

ig.

5)5)

For the exhaust mode

For the exhaust modeFor the exhaust mode

For the exhaust mode:

• Check the correct position of the exhaust hose

and connect it with the outlet opening.

• Pull up the inner shaft and fix the shaft cover to

the side with the bracket using the screws

2x ST4*8

(Fig. 6)

(Fig. 6)(Fig. 6)

(Fig. 6)

Installing the ac

Installing the acInstalling the ac

Installing the activated carbon

tivated carbontivated carbon

tivated carbon

filter for recirculation

filter for recirculation filter for recirculation

filter for recirculation

mode

modemode

mode

• Open the filter cover and remove the aluminum

grease filter.

• Place the carbon filter onto the air intake of the

extraction duct. Make sure that the mounting pins

on the extraction duct engage the mounting slots

of the carbon filter. Turn the filter clockwise until it

clicks into place.

• Reinstall the aluminum grease filter and close the

cover.

Electrical connection

Electrical connectionElectrical connection

Electrical connection

WARNING:

WARNING:WARNING:

WARNING:

• The installation to the mains supply must conform

to the local standards and regulations.

• Improper connection may cause to an electric

electric electric

electric

shock

shockshock

shock!

• Do not modify the appliance plug. If the plug does

not fit properly to the outlet, let install a proper

outlet by an authorized specialist.

• The accessibility of the power plug must be en-

sured to disconnect the appliance from the power

supply in case of emergency.

• Ensure that your mains power corresponds with

the specifications of the appliance. The specifica-

tions are printed on the rating label.

• Connect the mains cable to a properly installed

and earthed wall outlet.

• If the plug after installation is not accessible, a

corresponding disconnect device must be availa-

ble to meet the relevant safety regulations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann DU 771.1 G Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info