Bedienungsanleitung Bomann DU 773 (Seite 21 von 24) (Deutsch, Englisch)

688079

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

• Rinse the grease filter in a solution of hot water

and neutral detergent. Soak the filter in it.

• Then clean with a soft brush, rinse thoroughly with

hot water and allow drying.

• Alternatively, the grease filter can also be cleaned

in the dishwasher (up to 60°C). Slight discolora-

tion may occur. This does not affect the function

of the grease filter.

Replacing the activated carbon filter

Replacing the activated carbon filterReplacing the activated carbon filter

Replacing the activated carbon filter

The activated carbon filter prevents odors and must

depend on the use but be changed at least every six

months.

Order the carbon filter from your dealer or in our

online accessories shop, www.bomann

www.bomannwww.bomann

www.bomann-

-germany.de

germany.degermany.de

germany.de.

Use the reference number found under “Technical

Data”.

• See “Installing the activated carbon filter for recir-

culation mode”.

• Remove and dispose the old carbon filter.

Replacing the bulb

Replacing the bulbReplacing the bulb

Replacing the bulb

CAUTION:

CAUTION:CAUTION:

CAUTION:

Do NOT

NOTNOT

NOT remove the LED lighting cover!

The bulb may only be replaced by an authorized

specialist in case of a defect.

WAR

WARWAR

WARNING

NINGNING

NING:

• The light of LED lamps is very bright and can

damage the eyes. Never

. Never. Never

. Never look directly into the

LED light!

• Disconnect the appliance from the power supply

and allow the lamps to cool down before changing

the lamp. There is a risk of burns!

There is a risk of burns!There is a risk of burns!

There is a risk of burns!

NOTE

NOTENOTE

NOTE:

Order the lamps from your dealer or in our online

accessories shop www.bomann

www.bomannwww.bomann

www.bomann-

-germany.de

germany.degermany.de

germany.de.

Lamp data

amp dataamp data

amp data:

LED max. 2 x 2.0 W, DC 12V

ILCOS D Code after EN 61231: DBR-2/30-H-64

• Remove the grease filter. Carefully push the lamp

out of the holder through the hood body; pull out

the lamp and release the plug connection.

• Replace defect LED module and pin the two ends

of the plug-in device.

• Insert new lamp properly in the bulb holder. Re-

place the grease filter.

Troubleshooting

TroubleshootingTroubleshooting

Troubleshooting

Before you contact an authorized specialist

Before you contact an authorized specialistBefore you contact an authorized specialist

Before you contact an authorized specialist

Problem

ProblemProblem

Problem

Possible Cause / Solution

Possible Cause / SolutionPossible Cause / Solution

Possible Cause / Solution

Unit is not

working or not

properly

∙ Check the power supply.

∙ Check the power level.

Unit is not

working

efficiently

∙ Check the power level.

∙ Is the kitchen properly ventilated?

∙ Clean the grease filter. ∙ At recir-

culation mode, check the carbon

filter. ∙ Check the air outlet.

Light is not

working

∙ Check the bulb, see “Replacing

the bulb”.

Oil is dripping ∙ Clean the grease filter.

NOTE:

NOTE:NOTE:

NOTE:

If you are still having problems after following steps

above, contact your trader or an authorized techni-

cian.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann DU 773 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info