Bedienungsanleitung Bomann EBK 960 (Seite 6 von 16) (Englisch)

651992

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Preparing the worktop for

Preparing the worktop for Preparing the worktop for

Preparing the worktop for

installation of the hob

installation of the hobinstallation of the hob

installation of the hob

CAUTION:

CAUTION:CAUTION:

CAUTION:

Before cutting secure the outer

cutout

adhesive tape to avoid traces of jigsaw on the

top.

• The worktop must have a

minimum thickness of

30 mm, it

must lie horizontally and be sealed to

the wall side against overflowing liquids or moi

ture.

• The cut surfaces (cutout e

dges) must be sealed

with special varnish, silicone rubber or cast raisin

in order to p

revent swelling caused by humidity.

•

Clean and dry the worktop in the cutout area

thoroughly.

Worktop cutout

Worktop cutoutWorktop cutout

Worktop cutout

Prepare the cutout of the worktop

according to the

dimensional drawing.

Figures in mm

Installing the hob

Installing the hobInstalling the hob

Installing the hob

•

First check the factory fitted hob seal

frame to the integrity and the proper fit.

•

Put the hob with the connecting cable

with

the control panel to the front into the pr

pared cutout.

•

Make sure that the distances to the cutting a

equal on all four sides and that the seal is resting

on the worktop.

•

Fix the hob depending on the worktop thickness

by attaching the enclosed

brackets (3)

installation of the hob

installation of the hobinstallation of the hob

installation of the hob

cutout

edge with wide

adhesive tape to avoid traces of jigsaw on the

work-

minimum thickness of

must lie horizontally and be sealed to

the wall side against overflowing liquids or moi

dges) must be sealed

with special varnish, silicone rubber or cast raisin

revent swelling caused by humidity.

Clean and dry the worktop in the cutout area

according to the

Hob

Gasket

Bracket

Screw

First check the factory fitted hob seal

at the hob

frame to the integrity and the proper fit.

Put the hob with the connecting cable

first and

the control panel to the front into the pr

Make sure that the distances to the cutting a

equal on all four sides and that the seal is resting

Fix the hob depending on the worktop thickness

brackets (3)

from the

hob bottom at the provided holes and fasten them

with the screws (4).

Electrical connect

Electrical connectElectrical connect

Electrical connection

ionion

ion

Information for the

Information for the Information for the

Information for the

authorized expert

authorized expertauthorized expert

authorized expert

WARNING:

WARNING:WARNING:

WARNING:

•

The installation to the mains supply must conform

to the local standards and regulations.

•

Connecting the appliance to a domestic power

socket or using multiple sockets or extension c

bles is not permitted.

•

Improper connection may cause to an

shock

shockshock

shock!

•

Before connecting, ensure that the power supply

corresponds with the information on the rating l

bel (appliance bottom

) an

•

Fix the mains cable in the tension relief.

• The electric

al installation must have an isolation

device which lets you disconnect the appliance at

all poles from the power supply.

device shall be executed with a contact width of

min. 3 mm.

•

Arrange the mains cable in such a way that it

does not get

in contact with any hot components

of the appliance. Do not lead it over sharp edges

or corners.

Mains socket

Mains socketMains socket

Mains socket

The socket must be connected according to the

standards to a single-

pole circuit breaker. The co

nection is shown below:

NOTE

NOTENOTE

NOTE:

: :

L1L1

L1-brown L2

L2L2

L2-black P3

P3P3

P3-green

hob bottom at the provided holes and fasten them

authorized expert

authorized expertauthorized expert

authorized expert

The installation to the mains supply must conform

to the local standards and regulations.

Connecting the appliance to a domestic power

socket or using multiple sockets or extension c

Improper connection may cause to an

electric

electric electric

electric

Before connecting, ensure that the power supply

corresponds with the information on the rating l

) an

d the wiring diagram.

Fix the mains cable in the tension relief.

al installation must have an isolation

device which lets you disconnect the appliance at

all poles from the power supply.

The disconnect

device shall be executed with a contact width of

Arrange the mains cable in such a way that it

in contact with any hot components

of the appliance. Do not lead it over sharp edges

The socket must be connected according to the

pole circuit breaker. The co

yellow N1

N1N1

N1-blue N2

N2N2

N2-grey

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann EBK 960 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann EBK 960

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info