Bedienungsanleitung Bomann EHBC 559 (Seite 7 von 20) (Englisch)

688074

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

• The cut surfaces (cutout e

dges) must be sealed

with special varnish, silicone rubber or cast raisin

in order to prevent swell

ing caused by humidity.

•

Clean and dry the worktop in the cutout area

thoroughly.

Worktop cutout

Worktop cutoutWorktop cutout

Worktop cutout

Prepare the cutout of the worktop

according to the

dimensional drawing.

Dimensions in mm

Installing the hob

Installing the hobInstalling the hob

Installing the hob

•

Before installing the hob, the supplied gasket

must be moun

ted on the underside of the hob

frame.

For this place the hob with the hob top on

a padded surface to prevent it from damage.

NOTE

NOTENOTE

NOTE:

To avoid damage, place the hob with the top of

the cooking surface on a padded base.

• Place

the hob according to the hob

"Appliance

Overview" and with the connecting c

ble first

centrally into the prepared cutout of the

worktop. Make sure that the distances to the cu

ting are equal on all four sides and that the seal is

resting on the worktop.

•

Secure the hob from below with the supplied

clamps and screws on the worktop.

dges) must be sealed

with special varnish, silicone rubber or cast raisin

ing caused by humidity.

Clean and dry the worktop in the cutout area

according to the

Before installing the hob, the supplied gasket

ted on the underside of the hob

For this place the hob with the hob top on

a padded surface to prevent it from damage.

To avoid damage, place the hob with the top of

the cooking surface on a padded base.

the hob according to the hob

drawing under

Overview" and with the connecting c

centrally into the prepared cutout of the

worktop. Make sure that the distances to the cu

ting are equal on all four sides and that the seal is

Secure the hob from below with the supplied

clamps and screws on the worktop.

Installing the oven

Installing the ovenInstalling the oven

Installing the oven

• Put the appliance

with the connecting cable f

into the prepared cabinet a bit

• Do the connection

to the hob

mains, see "Electrical connection".

• Insert the oven

into the cabinet opening

. Make sure that the cable

(bent, squeezed or twisted)

•

Attach and secure the oven

screws on the side walls of the cab

vided mounting holes are visible after opening the

oven door on the left and right frame

Electrical connection

Electrical connectionElectrical connection

Electrical connection

Information for the

Information for the Information for the

Information for the

authorized expert

authorized expertauthorized expert

authorized expert

WARNING:

WARNING:WARNING:

WARNING:

•

The installation to the mains supply must conform

to the local standards and

•

Connecting the appliance to a domestic power

socket or using multiple sockets or extension c

bles is not permitted.

•

Improper connection may cause to an

shock

shockshock

shock!

•

Before connecting, ensure that the power supply

corresponds with the

information on the rating l

bel (appliance back)

and the wiring diagram.

•

The appliance is suitable for three

current (

220-240/380-

415V 3N

•

The appliance can be adjusted for single

current by a respective

bypass on the terminal

block,

based on the circuit diagram below. Select

with the connecting cable f

irst

into the prepared cabinet a bit

to the hob

as well as to the

mains, see "Electrical connection".

into the cabinet opening

complete-

. Make sure that the cable

s does not restricted

(bent, squeezed or twisted)

Attach and secure the oven

by using the supplied

screws on the side walls of the cab

inet. The pro-

vided mounting holes are visible after opening the

oven door on the left and right frame

authorized expert

authorized expertauthorized expert

authorized expert

The installation to the mains supply must conform

to the local standards and

regulations.

Connecting the appliance to a domestic power

socket or using multiple sockets or extension c

Improper connection may cause to an

electric

electric electric

electric

Before connecting, ensure that the power supply

information on the rating l

and the wiring diagram.

The appliance is suitable for three

-phase and AC

415V 3N

~ 50Hz

The appliance can be adjusted for single

-phase

bypass on the terminal

based on the circuit diagram below. Select

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann EHBC 559 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann EHBC 559

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info