Bedienungsanleitung Bomann EHBC 560.1 IX (Seite 7 von 20) (Englisch)

687854

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Cabinet opening and appliance dimensions

Cabinet opening and appliance dimensionsCabinet opening and appliance dimensions

Cabinet opening and appliance dimensions

Prepare the cabinet opening according to the dimen-

sional drawings.

Dimensions in mm

Preparing the worktop for

Preparing the worktop for Preparing the worktop for

Preparing the worktop for installation of the hob

installation of the hobinstallation of the hob

installation of the hob

CAUTION:

CAUTION:CAUTION:

CAUTION:

Before cutting secure the outer cutout edge with wide

adhesive tape to avoid traces of jigsaw on the work-

top.

• The worktop must be leveled horizontally and be

sealed on the wall side against overflowing liquids

or moisture.

•

The hob must be completely surrounded by min.

50 mm work surface.

• The cut surfaces (cutout edges) must be sealed

with special varnish, silicone rubber or cast raisin

in order to prevent swelling caused by humidity.

•

Clean and dry the worktop in the cutout area

thoroughly.

Worktop cutout

Worktop cutoutWorktop cutout

Worktop cutout

Prepare the cutout of the worktop according to the

dimensional drawing.

Dimensions in mm

Installing the hob

Installing the hobInstalling the hob

Installing the hob

NOTE

NOTENOTE

NOTE:

To avoid damage, place the hob with the top of the

cooking surface on a padded base.

• First check the factory fitted hob seal at the hob

frame to the integrity and the proper fit.

•

Attach the enclosed retaining clamps with the

screws in the provided holes laterally of the hob.

• Place the hob according to the hob drawing under

"Appliance Overview" and with the connecting ca-

ble first centrally into the prepared cutout of the

worktop.

• Make sure that the distances to the cutting are

equal on all four sides and that the seal is resting

on the worktop.

Installing the oven

Installing the ovenInstalling the oven

Installing the oven

• Put the appliance with the connecting cable first

into the prepared cabinet a bit.

• Do the connection to the hob as well as to the

mains, see "Electrical connection".

• Insert the oven into the cabinet opening complete-

ly. Make sure that the cables does not restricted

(bent, squeezed or twisted).

• Attach and secure the oven by using the supplied

screws on the side walls of the cabinet.

The provided mounting holes

(A) are visible after opening

the oven door on the left and

right frame

Electrical

Electrical Electrical

Electrical connection

connectionconnection

connection

Information for the

Information for the Information for the

Information for the authorized expert

authorized expertauthorized expert

authorized expert

WARNING:

WARNING:WARNING:

WARNING:

• The installation to the mains supply must conform

to the local standards and regulations.

• Connecting the appliance to a domestic power

socket or using multiple sockets or extension ca-

bles is not permitted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann EHBC 560.1 IX Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann EHBC 560.1 IX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info