Bedienungsanleitung Bomann EHBC 562 (Seite 7 von 20) (Englisch)

688073

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Dimensions in mm

Preparing the worktop for

Preparing the worktop for Preparing the worktop for

Preparing the worktop for

installation of the hob

installation of the hobinstallation of the hob

installation of the hob

CAUTION:

CAUTION:CAUTION:

CAUTION:

Before cutting secure the outer

cutout

adhesive tape to avoid traces of jigsaw on the

top.

•

The worktop must be leveled horizontally

sealed on the wall side against overflowing liquids

or moisture.

•

The hob must be

completely surrounded by min.

50 mm work surface.

•

The cut surfaces (cutout edges) must be sealed

with special varnish, silicone rubber

in order to prevent swelling caused by humidity.

•

Clean and dry the worktop in the cutout area

thoroughly.

Worktop cutout

Worktop cutoutWorktop cutout

Worktop cutout

Prepare the cutout of the worktop

according to the

dimensional drawing.

Dimensions in mm

Installing the hob

Installing the hobInstalling the hob

Installing the hob

NOTE

NOTENOTE

NOTE:

To avoid damage, place the hob with the top of the

cooking surface on a padded base.

•

First check the factory fitted hob seal at the hob

frame to the integrity and the proper

installation of the hob

installation of the hobinstallation of the hob

installation of the hob

cutout

edge with wide

adhesive tape to avoid traces of jigsaw on the

work-

The worktop must be leveled horizontally

and be

sealed on the wall side against overflowing liquids

completely surrounded by min.

The cut surfaces (cutout edges) must be sealed

with special varnish, silicone rubber

or cast raisin

in order to prevent swelling caused by humidity.

Clean and dry the worktop in the cutout area

according to the

To avoid damage, place the hob with the top of the

First check the factory fitted hob seal at the hob

frame to the integrity and the proper

fit.

•

Attach the enclosed retaining clamps with the

screws in the provided holes

• Place

the hob according to the hob

"Appliance

Overview" and with the connecting c

ble first centrally into the

prepared cutout of the

worktop.

•

Make sure that the distances to the cutting are

equal on all four sides and

on the worktop.

Installing the oven

Installing the ovenInstalling the oven

Installing the oven

• Put the appliance

with the connecting cable f

into the prepared cabinet a bit

• Do the connection

to the hob

mains, see "Electrical connection".

• Insert the oven into the

cabinet opening

. Make sure that the cable

(bent, squeezed or twisted)

•

Attach and secure the oven

screws on the side walls of the cabi

The provided mounting holes

(A)

are visible after opening

the

oven door on the left and

right frame

Electrical connection

Electrical connectionElectrical connection

Electrical connection

Information for the

Information for the Information for the

Information for the

authorized expert

authorized expertauthorized expert

authorized expert

WARNING:

WARNING:WARNING:

WARNING:

•

The installation to the mains supply must conform

to the local standards and regulations.

•

Connecting the appliance to a domestic power

socket

or using multiple sockets or extension c

bles is not permitted.

•

Improper connection may cause to an

shock

shockshock

shock!

•

Before connecting, ensure that the power supply

corresponds with the information on the rating

bel (door frame)

and the wiring

Attach the enclosed retaining clamps with the

screws in the provided holes

laterally of the hob.

the hob according to the hob

drawing under

Overview" and with the connecting c

prepared cutout of the

Make sure that the distances to the cutting are

equal on all four sides and

that the seal is resting

with the connecting cable f

irst

into the prepared cabinet a bit

to the hob

as well as to the

mains, see "Electrical connection".

cabinet opening

complete-

. Make sure that the cable

s does not restricted

(bent, squeezed or twisted)

Attach and secure the oven

by using the supplied

screws on the side walls of the cabi

net.

The provided mounting holes

are visible after opening

oven door on the left and

right frame

authorized expert

authorized expertauthorized expert

authorized expert

The installation to the mains supply must conform

to the local standards and regulations.

Connecting the appliance to a domestic power

or using multiple sockets or extension c

Improper connection may cause to an

electric

electric electric

electric

Before connecting, ensure that the power supply

corresponds with the information on the rating

la-

and the wiring

diagram.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann EHBC 562 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann EHBC 562

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info