Bedienungsanleitung Bomann GS 3181 (Seite 17 von 24) (Deutsch)

688044

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Assembling the doo

Assembling the dooAssembling the doo

Assembling the door handle

r handler handle

r handle

Remove the cover caps from the door outer side and

tighten the handle with the delivered screws into the

underlying holes. Put the included screw covers on.

Electrical connection

Electrical connectionElectrical connection

Electrical connection

WARNING:

WARNING:WARNING:

WARNING:

• The installation to the mains supply must conform

to the local standards and regulations.

• Improper connection may cause to an electric

electric electric

electric

shock

shockshock

shock!

• Do not modify the appliance plug. If the plug does

not fit properly to the outlet, let install a proper

outlet by an authorized specialist.

• The accessibility of the power plug must be en-

sured to disconnect the appliance from the power

supply in case of emergency.

CAUTION

CAUTIONCAUTION

CAUTION:

In case of disconnection or power failure:

- Wait for approx. 5 minutes before restarting.

- Check the operation settings.

• Ensure that your mains power corresponds with

the specifications of the appliance. The specifica-

tions are printed on the rating label.

• Connect the mains cable to a properly installed

and earthed wall outlet.

• If the plug after installation is not accessible, a

corresponding disconnect device must be availa-

ble to meet the relevant safety regulations.

Reverse the

Reverse the Reverse the

Reverse the door o

door odoor o

door opening

peningpening

pening

If required, the door openings can be moved from the

right (supplied condition) to the left side.

WARNING:

WARNING:WARNING:

WARNING:

When replacing the door stops, the appliance must

be disconnected from the power supply. Always un-

plug the appliance first.

NOTE

NOTENOTE

NOTE:

• When installing, ask another person to assist.

•

You possibly need:

screw wrench, Phillips screw-

driver as well as a thin-blade screwdriver.

• Remove the cover caps on

the top cover. Loosen the

screws underneath and re-

move the top cover.

• Transfer the blind cap of the

appliance cover at the oppo-

site side.

• Dismount the upper door

hinge. Open the appliance

door a little and lift it out of the lower door hinge.

• Remove the dummy cap (B)

and insert supplied dummy

cap (A). Place the appliance door safely aside.

NOTE

NOTENOTE

NOTE:

Keep the dummy cap (B) for another possible

door opening reverse.

• Tilt the appliance slightly backwards and block it

in this position. Unscrew the feet.

Dismount the foot bracket

and the lower door hinge.

• Attach the door hinge at the other appliance side,

after you have unscrewed the

hinge pin and used it from the

other hinge side. Transfer and fix the foot bracket

too. Turn in the feet accordingly.

• Replace the appliance upright. Put the appliance

door on the hinge pin and fix it in its intended po-

sition.

• Transfer the upper door hinge at the opposite

side, after you have unscrewed the hinge pin and

used it from the other hinge side.

Put the hinge pin in the hole of

the appliance door and fasten the hinge.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann GS 3181 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info