Bedienungsanleitung Bomann GSPE 890 (Seite 14 von 20) (Englisch)

687836

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Control lamp: lights up, when dishwasher salt

needs refilling.

8 The control lamps indicate the start delay

selection.

Starting a program

Starting a programStarting a program

Starting a program

• The water supply must be opened up to the max-

imum pressure.

• Load the dishwasher baskets.

• Fill in the detergent.

• Turn on the appliance.

• Set the required program options.

• Start the operation.

Changing the program

Changing the programChanging the program

Changing the program

CAUTION:

CAUTION:CAUTION:

CAUTION:

A program change should be done only a short time

after starting the program. Otherwise, maybe deter-

gent has been released and already drained rinse

water.

•

First press the Start/Pause button to stop the

current rinse program.

• Press the Program selection button for about

3 seconds.

• Select a new program and start the new

operation.

Forgot to add a dish?

Forgot to add a dish?Forgot to add a dish?

Forgot to add a dish?

WARNING:

WARNING:WARNING:

WARNING:

Open the door very carefully during operation, there

is a risk of water squirting out.

Dishware can be added any time before the deter-

gent dispenser opens.

• Press the Start/Pause button to stop the opera-

tion. Once the spray arms have stopped, you can

fully open the appliance door.

• Add forgotten dishware.

• Press the Start/Pause button, the operation will

continue after approx. 10 seconds.

At the end of program

At the end of programAt the end of program

At the end of program

CAUTION:

CAUTION:CAUTION:

CAUTION:

Allow the appliance to cool down a bit after the pro-

gram has ended, before you open it. This avoids that

steam escapes that causing long-term damages to

your furniture.

At the end of the rinse cycle will sound a series of

signals; then the unit goes into standby mode.

Turn off

Turn offTurn off

Turn off

• Turn off the appliance.

• Close the water supply, if necessary!

• Remove the dishes after cooling (see "Unloading

the dishwasher").

• Leave the appliance door slightly open until the

next rinse cycle to avoid odors.

• If the appliance is not in use for an extended peri-

od, disconnect it from the power supply!

Unloading the dishwasher

Unloading the dishwasherUnloading the dishwasher

Unloading the dishwasher

CAUTION:

CAUTION:CAUTION:

CAUTION:

Let the dishware cool down for about 15 minutes

before unloading. Hot dishes are sensitive to knocks.

NOTE

NOTENOTE

NOTE:

At the end of program there could be still water drops

inside the appliance.

• Open the appliance door and pull out the basket.

• To avoid water dripping from the upper basket

onto the dishes in the lower basket, it is advisable

to unload the appliance from the bottom up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann GSPE 890 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann GSPE 890

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info