Bedienungsanleitung Bomann KB 340 (Seite 16 von 24) (Englisch)

688030

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

• Avoid the installation:

Avoid the installation:Avoid the installation:

Avoid the installation:

- near heaters, next to a stove, direct sunlight or

any other heat sources;

- at locations with high humidity (e.g. outdoors,

bathroom), as metal parts would be suscepti-

ble to corrosion under such circumstances;

- near volatile or flammable materials (e.g. gas,

fuel, alcohol, paint, etc.), in rooms which may

have poor air circulation (e.g. garages).

- Do not expose the appliance any weather.

Electrical connection

Electrical connectionElectrical connection

Electrical connection

WARNING:

WARNING:WARNING:

WARNING:

• The installation to the mains supply must conform

to the local standards and regulations.

• Improper connection may cause to an electric

electric electric

electric

shock

shockshock

shock!

• Do not modify the appliance plug. If the plug does

not fit properly to the outlet, let install a proper

outlet by an authorized specialist.

• The accessibility of the power plug must be en-

sured to disconnect the appliance from the power

supply in case of emergency.

• Make sure that the voltage supply matches the

specifications on the rating label before

connecting.

• Connect the mains cable to a properly installed

and earthed wall outlet.

• If the plug after installation is not accessible, a

corresponding disconnect device must be availa-

ble to meet the relevant safety regulations.

Reverse the

Reverse the Reverse the

Reverse the door o

door odoor o

door opening

peningpening

pening

If required, the door opening can be moved from the

right (supplied condition) to the left side.

WARNING:

WARNING:WARNING:

WARNING:

When replacing the door stop, the appliance must be

disconnected from the power supply first.

NOTE

NOTENOTE

NOTE:

• Ask another person to assist.

•

You possibly need:

screw wrench, Phillips screw-

driver as well as a thin-blade screwdriver.

• Remove the plastic rivet (1) and hinge cover (2).

• Loosen the screws (3) and remove the door hinge

(4). Lift the unit door from the door hinge (6).

• Displace the dummy plug (5) of the appliance

door. Place the appliance door safely aside.

• Tilt the unit slightly backwards and block it in this

position.

• Disassemble the lower door hinge (6) incl. foot by

loosening the screws (7). Unscrew the separate

foot (8).

• Displace and fasten the door hinge (6) incl. foot

with the screws (7) accordingly. Screw in the

separate foot (8).

• Return the unit to the upright position. Place the

appliance door on the hinge pin and fix it in the

intended position.

• Displace and fasten the upper door hinge (4) with

the screws (3) accordingly.

• Put the plastic rivet (1) in the exposed hole and

replace the hinge cover (2).

• Check that the door is aligned vertically and

horizontally to ensure proper opening and closing

of the door.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann KB 340 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info