Bedienungsanleitung Bomann KG 180 (Seite 5 von 11) (Englisch)

552091

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

07/2012

- 2009/125/EC framework for the setting of ecodesign requirements for energy-using

- 643/2009/EC requirements for household refrigerating appliances.

MANUFACTURER DATA: Product is subject to changes and improvements.

NSTALLATION

Location

Sufficient ventilation around the device is necessary in order for the heat to dissipate properly and to

guarantee efficient cooling operation at low power consumption. For this purpose, leave sufficient

space around the device.

- Minimum clearance of 7,5 cm between rear side and wall,

- at least 10 cm on both sides and 10 cm on top of the device.

- Leave proper space in front of the device in order to open the door at an angle of 160°.

IMPORTANT:

- Do not expose the device to direct sunlight.

- Do not place near heaters, next to a stove or any other heat sources.

- Only install at a location with an ambient temperature suitable for the climate class of the device.

For information on the climate class, please refer to chapter “Specifications“ or to the rating label

located in the interior or on the rear side of the device.

- Do not use the device outdoors.

- Avoid installation at locations with high humidity (e.g. outdoors, bathroom), as metal parts would be

susceptible to corrosion under such circumstances.

- Do not place the device near volatile or combustible materials (e.g. gas, fuel, alcohol, paint, etc.)

and in rooms which may have poor air circulation (e.g. garages).

- Only place on a steady and safe surface.

- If the device is not horizontally leveled, adjust the feet accordingly.

Electrical connection

The kind of current (AC) and the voltage must be conform with the data of the rating label, located

inside or outside on the back of the unit. In case of heavy voltage fluctuations, it is recommended to

use an automatic alternating current regulator.

The plug, together with the grounding conductor, must fit into the wall socket. The mains plug must be

freely accessible.

Mains cable

- Do not extend or roll up the cable during operation.

- Also, the cable must not be near the compressor on the rear side, since latter one gets hot during

operation. In case of any contact, the isolation would be damaged resulting in electric leakage.

- The use of extension cables is not recommended.

- Do not connect the device to the mains with wet hands.

- Install the device for the wall socket to be freely accessible.

EVERSE

OOR

PENING

If required, the door openings can be moved from the right (supplied condition) to the left side.

WARNING: When replacing the door stops, the device must be disconnected from the power

supply. Always unplug the device first.

1. Use a flat bladed screw driver to remove the screw covers at the device cover. Unscrew the below

screws and remove the device cover.

2. Put the blind cap of the device cover at the opposite side.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann KG 180 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann KG 180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info