Bedienungsanleitung Bomann KG 7353 (Seite 29 von 32) (Deutsch, Englisch)

814351

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

• After everything has dried thoroughly, you can put

the appliance back into operation.

•

Depending on the model:

At least once a year,

wipe off the dust that has accumulated on the rear

wall of the unit and on the condenser (metal

grille). Use a soft brush or a vacuum cleaner for

this purpose.

Cleaning / replacing the door seal

Regularly check the seal for dirt, damage and air

tightness!

Checking the seal for air tightness

• Clamp a thin piece of paper at various points for

testing. The paper must be equally difficult to pull

through at all points.

Cleaning the gasket

• Clean the gasket with clear water only!

• CAUTION, grease and oil makes the seal porous

and brittle. Wipe up grease or oil immediately with

a damp, clean cloth.

Replacing the seal

• Remove the contents of the appliance and, if

necessary, defrost the unit. Pay attention to how

the old gasket is attached. Most gaskets are only

plugged in.

• Remove the worn gasket rubber by removing it

from the groove. Carefully clean the appliance

door and the groove below the rubber and re-

move any adhesive residue.

• Attach the new rubber. If necessary, heat the

rubber seal with a hair dryer or hot water and

shape it by hand. Start pressing the gasket in one

corner and then press it around the door into the

groove provided for this purpose.

• Continue to check the seal regularly for dirt and

damage!

Defrosting

CAUTION:

Never use metal objects (e.g. knifes) to remove ice

from the evaporator, it can be damaged.

During the defrosting process in the fridge, the water

drops drain off at the back wall of the cooling cham-

ber. The thaw water running through a channel, is

collected in a drip tray located on the compressor,

from which it then evaporates. Make sure that the

defrost water drain channel does not become

clogged. A slight formation of ice on the interior rear

wall during operation is normal.

A permanently high power level can lead to in-

creased ice formation

→ set a lower power level and

wipe the interior of the appliance dry.

To achieve better cooling and to save energy, defrost

the freezer regularly:

• To start the defrosting process, disconnect the

appliance from the power supply.

• Remove the appliance content and keep covered

at a cool location.

• When the ice has melted, wipe the condensate

away and dry the appliance interior.

• Then you may restart the appliance by connecting

the plug and turning the temperature control.

Changing the light

CAUTION:

Do NOT remove the cover of the light. The LED light

may be replaced / repaired in case of failure / defect

only by an authorized specialist.

Notes for the authorized specialist!

Lamp data: DC12V, max. 1,5 W

This product contains a light source of energy effi-

ciency class G.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann KG 7353 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info