Bedienungsanleitung Bomann KSE 327 (Seite 6 von 16) (Englisch)

552039

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

10/2013

NSTALLATION

Location

Sufficient ventilation around the device is necessary in order for the heat to dissipate properly and to

guarantee efficient cooling operation at low power consumption. For this purpose, leave sufficient

space around the device. Please also refer to chapter “Built-in“.

- Minimum clearance of 5 cm between rear side and wall,

- at least 1 cm on both sides.

- Leave proper space in front of the device in order to open the door at an angle of 160°.

IMPORTANT:

- Do not expose the device to direct sunlight.

- Do not place near heaters, next to a stove or any other heat sources.

- Only install at a location with an ambient temperature suitable for the climate class of the device.

For information on the climate class, please refer to chapter “Specifications“ or to the rating label

located in the interior or on the rear side of the device.

- Do not use the device outdoors.

- Avoid installation at locations with high humidity (e.g. outdoors, bathroom), as metal parts would be

susceptible to corrosion under such circumstances.

- Do not place the device near volatile or combustible materials (e.g. gas, fuel, alcohol, paint, etc.)

and in rooms which may have poor air circulation (e.g. garages).

Electrical connection

The kind of current (AC) and the voltage must be conform to the data of the rating label, located inside

or outside on the back of the unit. In case of heavy voltage fluctuations, it is recommended to use an

automatic alternating current regulator.

The plug, together with the grounding conductor, must fit into the wall socket. The mains plug must be

freely accessible.

Mains cable

- Do not extend or roll up the cable during operation.

- Also, the cable must not be near the compressor on the rear side, since latter one gets hot during

operation. In case of any contact, the isolation would be damaged resulting in electric leakage.

- The use of extension cables is not recommended.

- Do not connect the device to the mains with wet hands.

- Install the device for the wall socket to be freely accessible.

EVERSE

OOR

PENING

If required, the door opening can be moved from the right (supplied condition) to the left side.

WARNING: When replacing the door stop, the device must be disconnected from the power sup-

ply. Always unplug the device first.

- Tilt the device slightly backwards and block it in this position in order to avoid the slipping out of the

door.

- Dismount the upper stop plate and the underlying door hinge by loosening the screws.

- Take the door carefully down and place the door on a padded surface to prevent it from scratches.

- Unscrew the lower brackets and mount them each on the corresponding opposite sides.

- Replace the device upright again. Put the door on the lower hinge pin and fix the door to its proper-

ty position.

- Attach the upper door hinge to the corresponding opposite side and mount the stop plate again by

using the screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann KSE 327 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann KSE 327

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info