Bedienungsanleitung Bomann KSE 336 (Seite 20 von 28) (Deutsch, Englisch)

651993

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Install the power cord so that the appli-

ance can be easily connected after

installation. Slide the appliance into the

build-in opening until the stop plate (A)

abuts the furniture.

Press the rubber seal between the

appliance and built-in furniture firmly

(on the side without hinge).

Open the appliance door. Push the

appliance side, which is located oppo-

site the hinges, against the built-in

furniture. Arrange the appliance for a

secure, vertical position, fix it with the

supplied screws and put the protective

cap (B) on.

Separate the parts b, c and d of part a.

In consideration of the shown distanc-

es, hold the guide (a) at the top and

bottom inside of the furniture door; mark

the positions of the drill holes. After

drilling, fix the guide with the screws

provided.

Insert the cover (c) until it clicks in the

guide (a).

Fully open the appliance and furniture

door and join them together. Slide the

bracket (b) in the guide (a) and mark

the drill holes. Remove the bracket and

drill Ø 2 mm holes with about 8 mm

distance to the outer door edge. Put the

bracket on again; secure it with the

screws provided.

If an aligning of the furniture door is

necessary, use the slot spacing. Check

if the door is arranged vertical as well

as horizontal, so that a smooth opening

and closing of the door is ensured.

Insert the cover (D) until it clicks on the

angle (B).

Sta

StaSta

Startup / Operation

rtup / Operationrtup / Operation

rtup / Operation

Prior to first use

Prior to first usePrior to first use

Prior to first use

CAUTION

CAUTIONCAUTION

CAUTION:

After transport, the appliance should be left standing

upright for about 4 hours before connecting to the

power supply. Nonobservance could lead to malfunc-

tion of the cooling system and causes an appliance

breakdown.

Clean the appliance interior including all accessory

parts. Consider the instructions which we provide in

the chapter “Cleaning and Maintenance”.

Starting the appliance

Starting the applianceStarting the appliance

Starting the appliance

• Connect the appliance to the power supply.

• Operate the temperature control. See also the

following section "Settings".

Settings

SettingsSettings

Settings

Setting [0] means that the appliance is in the off

state. Turn the temperature control clockwise, start-

ing from this setting; the appliance will turn on auto-

matically.

The power levels [1–7] regulates the different values

of the internal temperature.

Setting 0

Setting 0Setting 0

Setting 0

Setting 1

Setting 1Setting 1

Setting 1

Setting 7

Setting 7Setting 7

Setting 7

Off state Lowest setting

(warmest inside

temperature)

Highest setting

(coldest inside

temperature)

Note that the temperature will change depending on

the ambient temperature, frequency of door opening

and the amount of food in the appliance.

During initial operation, turn the temperature control

to the highest setting first, until the appliance has

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann KSE 336 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info