Bedienungsanleitung Bomann KSG 7280.1 (Seite 21 von 24) (Deutsch, Englisch)

814353

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Cleaning and Maintenance

WARNING:

• Always disconnect the appliance from the power

supply before cleaning and user maintenance.

• Do not use steam cleaners for cleaning the appli-

ance; moisture could enter electrical components.

Risk of electric shock! Hot steam could damage

the plastic parts.

• The unit must be dry before restarting operation.

CAUTION:

• Do not use a wire brush or other sharp, abrasive

items.

• Do not use any acidic or abrasive detergents.

• Do not damage the refrigerant circuit.

Cleaning the appliance including interior

To keep dirt and germs at bay, clean the appliance

regularly!

• First clear out the contents of the appliance and

store it in a cool place. Remove all moving parts

such as shelves or drawers.

• Clean the interior of the appliance, the exterior

surfaces and the accessories with lukewarm wa-

ter and a mild cleaning agent; or with a clean,

damp microfiber cloth without cleaning agent.

• Clean the thaw water discharge channel / opening

carefully e.g. with a pipe cleaner.

• After everything has dried thoroughly, you can put

the appliance back into operation.

•

Depending on the model:

At least once a year,

wipe off the dust that has accumulated on the rear

wall of the unit and on the condenser (metal

grille). Use a soft brush or a vacuum cleaner for

this purpose.

Cleaning / replacing the door seal

Regularly check the seal for dirt, damage and air

tightness!

Checking the seal for air tightness

• Clamp a thin piece of paper at various points for

testing. The paper must be equally difficult to pull

through at all points.

Cleaning the gasket

• Clean the gasket with clear water only!

• CAUTION, grease and oil makes the seal porous

and brittle. Wipe up grease or oil immediately with

a damp, clean cloth.

Replacing the seal

• Remove the contents of the appliance and, if nec-

essary, defrost the unit. Pay attention to how the

old gasket is attached. Most gaskets are only

plugged in.

• Remove the worn gasket rubber by removing it

from the groove. Carefully clean the appliance

door and the groove below the rubber and remove

any adhesive residue.

• Attach the new rubber. If necessary, heat the rub-

ber seal with a hair dryer or hot water and shape it

by hand. Start pressing the gasket in one corner

and then press it around the door into the groove

provided for this purpose.

• Continue to check the seal regularly for dirt and

damage!

Defrosting

CAUTION:

Never use metal objects (e.g. knifes) to remove ice

from the evaporator. Otherwise, it can be damaged.

During defrosting water drops drains off at the back

of the cooling chamber. The thaw water running

through a channel, is collected in a drip tray located

on the compressor, where it will evaporate. Make

sure the water discharge opening does not get

clogged. A light formation of ice on the interior back

during operation is normal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann KSG 7280.1 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info