Bedienungsanleitung Bomann TSG 7404 (Seite 54 von 112) (Deutsch, Englisch, Holländisch, Spanisch, Polnisch)

814369

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

CAUTION:

• For proper operation, the appliance must be con-

nected professionally. The data of inlet and outlet

as well as the electrical connection values must

meet the required criteria.

• It is recommended that the installation, water

connection and electrical connection, be carried

out by a specialist.

Installation location

• Place the appliance so that all controls are easily

to reach, and the appliance door can open without

being impeded.

• Take care of a solid and horizontal position of the

appliance.

• Power cord and water hoses may not kinked or

squashed.

• Avoid the installation:

- near heaters, next to a stove, direct sunlight or

any other heat sources;

- at locations with high humidity (e.g. outdoors),

as metal parts would be susceptible to corro-

sion under such circumstances;

- in rooms where the temperature could drop

below freezing. Do not expose the appliance

any weather.

- near volatile or flammable materials (e.g. gas,

fuel, alcohol, paint, etc.).

Water connection

CAUTION:

• The Installation of the water supply must conform

to the local laws and regulations.

• Use the new supplied hose set to connect the

appliance to the water supply. Do not reuse old or

used connection sets.

• If the water pipe is new or long time not used,

ensure before connecting to the water system,

that the water is clear and free from contamina-

tion.

NOTE, the connection to the water mains may only

be made in accordance with DIN EN 1717 of the

drinking water ordinance. A suitable safety device

against drinking water contamination through back-

flow must be installed.

Notes on inlet hose safety system (delivery scope

depending on model)

The safety system consists of a double-walled inlet

hose. It guarantees to cut off the water supply when

leakage of the inner hose. Switching off the water

supply leads over an electronic contact.

If necessary, you can order an inlet hose safety sys-

tem from your dealer or in our online accessories

shop, www.bomann-germarny.de. To order, use the

reference number found under

“Technical data”.

Connect the water inlet hose (cold water connection)

NOTE:

The water pressure must be between 0.04-1.0 MPa.

With higher pressure: use a pressure regulator.

• Connect the water inlet hose to a

water thread with ¾“. Screw the

hose firmly in the direction of the

screw thread; pay attention for a

tight fit.

• Connect the other end of the inlet

hose to the inlet valve on the ap-

pliance back; pay attention for a

tight fit too.

Hot water supply

The dishwasher can be supplied with a water tem-

perature of not more than 60°C. Supplying the appli-

ance with hot water, the rinse running time is short-

ened but the cleaning effect can be slightly reduced.

The connection to the hot water valve must be done

in the same manner as described for the cold water

connection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann TSG 7404 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info