Bedienungsanleitung Bomann VSE 328 (Seite 11 von 14) (Englisch)

552043

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

11/2013

- Allow warm dishes to cool down before putting them in the device.

- Do not open the door longer than necessary.

- Only set the temperature as low as needed. The ideal temperature in fridge is +7°C.

It should be measured in the upper shelf, as far as possible in the front.

- Avoid opening all freezer compartments at the same time.

- Make sure that the temperature in the freezer does not rise above -18°C.

- The freezer should be defrosted regularly.

- Always keep the condenser – metal grid on the rear side (not at all models) – clean.

- Make sure the door sealing is in good order for the door to close properly.

AINTENANCE

LEANING

Cleaning and Care

For hygienic reasons, the appliance interior and accessories parts should be cleaned regularly.

WARNING:

- Always disconnect the plug or turn off/ unscrew the fuse before cleaning. Pull the plug and not the

cable.

- Do not use steam cleaners for cleaning the device; moisture could enter electrical components.

Risk of electric shock! Hot steam could damage the plastic parts. The device must be dry before

restarting operation.

- Essential oils and organic solvents, such as the juice of lemon or orange skin, butanoic acid or

cleaning agents containing acetic acid can damage plastic parts. Prevent contact of any part with

such substances. Do not use abrasive cleaning agents.

- The appliance must be dry before it is placed back into service.

Please do as follows:

- Remove all food and keep covered at a cool location.

- Use warm water and a mild detergent for cleaning the interior (including rear side and bottom in-

side).

- Check the water drain hole on rear wall inside the fridge. Clear a blocked drain hole with a small

peg.

- Clean the condenser at rear side (not at all models) once a year by using a soft brush or vacuum

cleaner.

- After thorough drying, restart operation.

WARNING:

- Do not bend the cooling coils.

- Do not use arenaceous abrasives.

Light - replace the bulb

Lamp specifications: 220-240V, max. 10W

To turn off the device, set the temperature control to setting 0 - OFF.

Disconnect the plug or turn off the fuse!

• Remove the screw from the lamp cover.

• Press on the lamp cover and remove to the back.

• Replace the defect illuminant.

• Reattach the lamp cover and fasten the screw.

• Reconnect the device and turn on.

Repairs

WARNING: Servicing of electric devices must be conducted by qualified experts only. Incorrect or

improper repairs constitute a risk for the user and will void the warranty!

What if . . . Troubleshooting

The design of the device ensures a trouble-free operation as well as a long life cycle. Nevertheless, if

any defect occurs during operation, please check if it is caused by improper operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann VSE 328 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann VSE 328

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info