Bedienungsanleitung Bomann WA 5612 (Seite 6 von 14) (Englisch)

552034

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

06/2012

NSTALLATION

Remove the Transit Bolts

Before using this washing machine, transport bolts must be removed from the backside of this ma-

chine. Loosen all bolts with spanner and then remove them and keep the transport bolts properly for

future use/transport. Plug the holes with the transit bolts caps supplied.

WARNING: Should the bolts aren’t removed, there could be serious damages during operation.

Location

- The device must be installed in a clean place, where dirty does not build up.

- Do not expose the device to direct sunlight.

- Do not place near heaters, next to a stove or any other heat sources.

- Avoid installation at locations with high humidity (e.g. outdoors), as metal parts would be suscepti-

ble to corrosion under such circumstances.

- Do not install in rooms where the temperature could drop below freezing. Do not expose the device

any weather.

- Do not place the device near volatile or combustible materials (e.g. gas, fuel, alcohol, paint, etc.).

- Only place on a steady and safe surface in order to reduce vibration and noise to a minimum.

- If the ground is evidently uneven (the maximum allowed tilt angle is 2°), it must be balanced, oth-

erwise the unit is wrong, vibrates or moves.

- If the floor is uneven, adjust the adjustable feet.

- A good ventilation around the unit is required so the heat can be derived correctly. A distance of

approx. 10 cm from the wall is required.

- The mains plug must be freely accessible.

Feet Adjustment

Take care to a firm and horizontal position of the dryer. If the

machine moves adjusts the feet. Loosen the locknuts with a

spanner.

Adjust the feet: to lower the dryer by turning right and to

ascend it by turning left. Tighten the locknut with the spanner

after insuring the device is leveled.

Once the position is fixed, you need to check the stability.

If not, repeat the action till it is leveled.

NOTE:

- The locknuts must be tightened after adjustment. Any looseness can cause vibration and noise.

- The feet must never be removed. Do not restrict the floor clearance through deep pile carpets,

strips of wood or similar. This might cause heat build-up which would interfere with the operation of

the appliance.

Water Connection

Install the Water Drain Hose

There are two ways to place the end of drain hose:

- Hang into a sink or trough.

- Connect it to the branch drain pipe of the trough.

If the outlet spigot has not been used before, remove any blanking plug that may be in place.

Push the drain hose onto the spigot and secure with a clip if required, ensure a loop is formed in the

drain hose to prevent waste from the sink entering the washing machine.

If you need a drain hose extension, make sure to use a similar drain hose, but it must be no longer

than 4 meters; otherwise the washing effect could be reduced.

Locknuts

Adjustable feet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bomann WA 5612 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bomann WA 5612

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info