Bedienungsanleitung Bompani BO643 (Seite 19 von 92) (Englisch, Holländisch, Französisch, Italienisch)

476985

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

- Avoid sharp bends in the pipe and keep it

well away from hot surfaces.

References to the regulations covering the

gas connection to the appliance: ISO 7-1.

ADAPTING TO DIFFERENT TYPES OF

GAS

If the cooker is not already preset to operate

with the type of gas available, it must be con-

verted. Proceed as follows:

- Replace the injectors (see table on page

17);

- regulate the primary air flow;

- regulate the minimum settings.

N.B.: every time you change the type of gas,

indicate the new type of gas on the serial

number label.

REPLACING THE HOB BURNER INJEC-

TORS (fig. 4)

- Lift off the pan stands, flame caps and burn-

ers

- unscrew the screws which secure the hob

(if any), lift it at the front and rest it against

the lid, fixing it with adhesive tape;

- remove the mixer pipes and replace the

injectors using a 7 mm socket wrench.

REPLACING THE OVEN BURNER INJEC-

TOR (Fig. 5)

- Loose the screw securing the oven bottom;

- remove the oven bottom (push back and

raise);

- remove the oven burner, after taking out its

fixing screw;

- replace the injector, using a 7 mm socket

wrench.

REPLACING THE GRILL BURNER INJEC-

TOR (Fig. 6)

- Remove the burner after taking out the two

screws which secure it;

- replace the injector using a 7 mm socket

wrench.

IMPORTANT:

- Never over-tighten the injectors;

- after replacing, check that all the injectors

are airtight.

REGULATING THE BURNER AIR

Refer to the table below (indicative values)

for regulation of the gap H in mm (fig. 4 for

the hob, fig. 6 for the grill).

Check operation of the burner:

- Ignite the burner at maximum flame;

- the tongue of the flame must be clear and

with no yellow tip, and must adhere closely

to the burner. If too much air is supplied,

the flame detaches from the burner and

may be dangerous. If the air supply is in-

sufficient, the flame has a yellow tip and

soot may form.

SETTING HOB BURNER MINIMUM LEV-

ELS

If the cooker is to work on bottled gas (bu-

tane/propane), the tap by-pass must be

screwed right down.

The cooker may be equipped with type A

taps, with by-pass inside (accessed by in-

serting a small screwdriver into the rod) or

type B taps, with by-pass on the outside on

the right (accessed directly). See figure 7.

If the cooker is to work on natural gas, pro-

ceed as follows for both types of tap:

- Ignite the burner at maximum flame;

- pull off the knob, without using a lever

against the control panel, which might be

damaged;

- access the by-pass with a small screwdriver

and back off by about 3 turns (turning the

screwdriver anti-clockwise);

- turn the tap rod anti-clockwise again until it

stops: the burner will be at maximum flame;

Burner G20 20mbar G30 28-30mbar

G31 37mbar

Auxiliary 3 4

Semi-rapid 3 4

Rapid 4 6

Ultra-rapid 5 6

Oven -- --

Grill 3 7

Installation

334766-01 7-02-2003, 15:5319

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bompani BO643 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info