Bedienungsanleitung Bompani BO650 (Seite 20 von 92) (Englisch, Holländisch, Französisch, Italienisch)

476988

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

- screw the by-pass slowly back in, without

pushing the screw-driver, until the flame has

apparently shrunk to 1/4 of the maximum

size, checking that it is sufficiently stable

even in quite strong draughts.

SETTING OVEN BURNER MINIMUM LEV-

ELS

If the cooker is to work on bottled gas (bu-

tane/propane), the thermostat by-pass must

be screwed right down.

If the cooker is to work on natural gas, pro-

ceed as follows:

- Remove the oven bottom (push towards the

back and raise);

- ignite the oven burner, turning the knob

pointer to the maximum setting;

- shut the oven door;

- access the thermostat or tap by-pass (see

fig. 8);

- back off the thermostat by-pass by about 3

turns;

- after 5 or 6 minutes, turn the knob pointer

to the minimum setting;

- slowly re-tighten the by-pass, watching the

flame decrease in size through the window

in the closed oven door until the tongue of

the flame is about 4 mm long. Never keep

the flame too low. It must be stable even

when the oven door is opened or closed

quickly;

- turn off the burner and replace the oven

bottom.

CONNECTING TO THE ELECTRICAL

MAINS

Before making the connection, check that:

- the mains voltage is as indicated on the

nameplate;

- the earth connection is in good working or-

der.

If the socket is not easily accessible, the in-

stallation engineer must provide a switch with

a contact breaking gap of 3 mm or more.

If the appliance power lead is not fitted with

a plug, use an approved standard type, re-

membering that:

- the green-yellow wire must be used for the

earth connection;

- the blue wire is the neutral;

- the brown wire is live;

- the lead must never touch hot surfaces over

about 75 degrees C;

- replacement leads must be of type H05RR-

F or H05V2V2-F of suitable size (see dia-

grams in fig. 2).

- if the appliance is supplied without lead,

using type H05RR-F or H05V2V2-F cable

of suitable size (see diagrams in fig. 2).

IMPORTANT: the manufacturer declines all

liability for damage due to failure to comply

with the regulations and standards in force.

Check that the appliance is correctly con-

nected to the earth (see diagrams in fig. 2 at

the back of the manual).

FOR COOKERS WITH ELECTRIC IGNI-

TION

The correct gaps between the electrode and

the burner are shown in figures 4, 5 and 6.

If no spark is generated, do not keep on try-

ing as this might damage the generator.

Possible causes of malfunctions:

- spark plug damp, dirty or broken;

- electrode-burner gap not correct;

- spark plug wire broken or without sheath-

ing;

- spark discharging to earth (to other parts

of the cooker);

- generator or microswitch damaged;

- air has built up in the pipes (particularly if

the cooker has been out of use for a long

time);

- air-gas mixture incorrect (poor fuel setting).

THE SAFETY DEVICE

The correct gap between the end of the ther-

mocouple sensor and the burner is shown in

figures 4, 5 and 6.

To check that the valve is working properly,

proceed as follows:

- ignite the burner and leave it to work for

about 3 minutes;

- turn off the burner by returning the knob to

Installation

334766-01 7-02-2003, 15:5320

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bompani BO650 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info