Bedienungsanleitung Boneco AOS 7142 (Seite 9 von 18) (Englisch)

497119

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

A) On/Off dial

You can switch the unit on or off by pressing button A. This

button is also used to reset the cleaning indicator light (by

holding down).

B) Hygrostat (setting the humidity level)

By pressing multi-functional button B (vertical) you can

set the desired humidity level in %. A relative humidity of

between 40 and 60% is recommended. The accuracy of

measurement is +/- 5%. The unit will switch off when the

moisture level exceeds the desired setting. During selection

the target value is displayed. The display will automatically

show the current value after a few seconds.

Operation 7142 C) Timer

Using multi-functional button C (horizontal), the opera-

tion time can be set adjustable between 1 and 8 hours.

Symbol G shows the operating period that has been set

(1h/2h/3h/4h/5h/6h/7h/8h). The display will automatically

show the current value after a few seconds.

D) Mist output (regulating mist output)

By repeatedly pressing button D you can control the mist

output. The LO/ME/HI display (symbol H) shows which of

the three levels (low/medium/high) you have selected.

E) Operation with pre-heating (warm mist)

Button E is used for switching the pre-heating on and off

(symbol I lights up). As a result, the water is pre-heated

to a temperature of 176 °F (80 °C) before entering the

nebulizer space. It takes approx. 10 to 15 minutes for the

water in the base to warm up. The mist now leaves the

humidifier at a pleasant temperature of 104 °F (40 °C). The

advantage of this is that the room temperature does not

drop and, in addition, it significantly improves the water

quality maintenance.

F) Automatic mode and Sleep mode

The automatic and sleep modes can be activated by pres-

sing button F. By pressing the button once, the automatic

function is switched on (symbol J appears on the display),

maintaining the optimum humidity subject to the tempera-

ture. Control takes place by means of output quantity and

pre-set target value. If the sleep function is switched on

(the symbol K appears on the display), the target humidity

is 60%; the operation time is automatically set at 6 hours;

the heating is switched on. In addition, the output quantity

is also controlled subject to the difference between the

target value and the actual value.

The Timer cannot be changed in either mode. If other

buttons are pressed, the unit will no longer be in auto or

sleep mode.

K L I M

L) Empty indicator

The water level is easy to see, thanks to the transparent

water tank. The appliance also alerts you when the water

tank is empty. The empty indicator is illuminated (symbol L).

Please read the chapter «Filling the tank» for more informa-

tion. The Symbol L may stay illuminated for some seconds

with a refilled tank until the base is filled with water.

M) Cleaning indicator

If symbol M and «CLEAN» appear on the display, the appli-

ance should be cleaned as recommended by the manufac-

turer. This symbol comes on automatically every 2 weeks,

depending on the level of use. The display can be reset by

holding down button A until the light disappears.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Boneco AOS 7142 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info