Bedienungsanleitung Bontrager RIDEtime Elite Computer plus (Seite 1 von 2) (Englisch)

775470

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

About this product

IMPORTANT: To use the RIDEtime Elite computer, you must have an ANT+ compatible speed, cadence,

or power sensor mounted on your bicycle.

Compatible sensors:

• Bontrager Duo Trap – PN 508126

• Bontrager Duo Trap S – PN 437960

• Bontrager Interchange Combo – PN 438482

• Bontrager ANT+/BLE Softstrap Heart Rate Belt Kit – PN 519606

• Other ANT+ compatible sensor

To set up any other sensor, please refer to the manual that came with your sensor.

When riding your bicycle, do not stare at the computer for a long time. If you do not watch the road,

you could hit an obstacle which might cause you to lose control, fall, and cause injury.

WARNING

Bontrager

RIDEtime Elite Computer

plus

Duo Trap S Sensor

www.bontrager.com

PN 580968

Parts list

RIDEtime Elite Computer

1 2

Install battery

Install computer mount

1. Shim use: Determine the diameter of your handlebar.

• Use the thin shim with a 31.8mm handlebar.

• Use the thick shim with a 25.4 or 26.0mm handlebar.

• Use no shims with a 35mm handlebar.

• Use both shims with a 22.2mm handlebar.

2. Remove the rubber cover over the mounting clamp bolt.

3. Use a 2.5mm hex wrench to torque the bolt to 0.8 N-m (7 in-lb).

4. Replace the rubber cover over the clamp bolt.

NOTE: The mount is not to be used with a cell phone.

Mount computer

Understanding the instructions

Button

location

Quick

press

Multi

press

Long press

(2 seconds)

Front

Rear

•

1•

•

Duo Trap S

1. Gasket (alloy bikes)

2. Sensor with grommet and 2mm spacer

installed (carbon bikes)

3. 8mm bike mounting screw

4. Speed magnet (wheel)

5. CR2032 battery

6. Cadence band shim

7. Large cadence band (crank) (26mm)

W519998

8. Small cadence band with magnet

(crank) (9mm) W519999

9. Xsmall cadence band with magnet

(crank) (4mm) W534154

10. Plug (large cadence band)

8107

3 4

Install battery

Install Duo Trap S sensor (alloy bikes)

1. Remove the Duo Trap S cover from the chainstay.

2. Remove the grommet from the sensor.

3. Install the gasket onto the sensor with the notch facing forward as shown.

4. Install the sensor and gasket into the chainstay.

5. Hold the sensor into place and install the 8mm screw.

6. Use a 2.5mm hex tool to tighten the sensor.

Install Duo Trap S sensor (carbon bikes)

1. Remove the Duo Trap S cover from the chainstay.

2. Remove the grommet from the sensor.

3. Fully insert the grommet into the chainstay. Make sure the grommet is ﬂush with the chainstay.

4. Install the sensor into the grommet in the chainstay.

HINT: Hold the grommet in place with one hand and insert the sensor with the other hand as shown.

5. Hold the sensor in place and use a 2.5mm hex to install and tighten the 8mm screw.

NOTE: Make sure the 2mm spacer is installed in the grommet before you tighten the screw.

Mount speed magnet

1. Tighten the speed magnet on a spoke

2. Align the speed magnet with the marking on the sensor.

3. If necessary, rotate the magnet 90˚ or 180˚ to achieve sensor clearance.

4. Rotate the wheel and look for a red LED in the sensor to verify the magnet and sensor are in

alignment.

NOTE: The LED will illuminate for the ﬁrst 10 revolutions only.

Install small cadence magnet

1. Remove the non driveside pedal and install the small cadence magnet on the crank arm with the thick

side nearest to the chainstay.

2. Align the magnet with the sensor.

• Alloy bikes: Align the magnet with the line on the sensor.

• Carbon bikes: Place the magnet 135mm or 145mm from the center of the bottom bracket to the

center of the magnet

3. Rotate the crank backwards. Look for the green LED on the cadence sensor to verify the magnet is

correctly aligned.

NOTE: The LED will illuminate for the ﬁrst 10 revolutions only.

4. Optional: If the magnet is aligned but the LED does not illuminate, place a cadence band shim

underneath the appropriate magnet.

5. If the small band does not ﬁt between the crank and the chainstay, use the XS (4mm) cadence

band provided.

Install large cadence magnet

1. Remove the plastic cap from inside the small cadence band.

2. Remove the magnet from inside the small cadence band.

3. Insert the magnet fully inside the large cadence band so it is ﬂush against the inside of the cavity.

4. Insert the plastic plug into the cavity of the large cadence band to hold the magnet in place.

5. Follow the steps in the Small cadence magnet installation to complete this installation.

•

1•

•

4•

m2.5N

•

4•

4a •

4b •

2.5Nm

•

90˚ 180˚

•

a•

b•

•

2145mm

135mm

•

3•

•

1•

2•

•

4•

Selection note:

Grey color represents

ﬂashing characters that

show selected value.

Shows number of digits

to be set.

Screen icon Description

Speed sensor is connected.

Flashing if searching for sensor.

Cadence sensor is connected.

Flashing if searching.

Heart rate monitor is connected.

Flashing if searching.

Power meter is connected.

Flashing if searching.

A service interval has been

reached. Flashing is a prompt

to clear.

Transmitter signal when

connected to compatible lights.

Flashing if searching.

Battery life is sufﬁcient.

Replacement when only

1/3 indicated.

BPM

RPM

KPH

MPH

Enter and exit setup modes

Front button

Rear button

AC button

Road Mountain City

Size Code Size Code Size Code

700:23* 2124 29:2.2* 2340 700:28* 2164

700:25 2136 29:2.3 (2.35) 2359 700:32 2190

700:28 2164 29:3.0 2413 700:35 2209

700:32 2190 27.5:2.2 2221 700:38 2227

700:35 2209 27.5:2.4 2253 700:40 2240

700:38 2227 27.5:2.8 2309 700:42 2253

700:40 2240 27.5:3.8 2400 700:45 2271

700:42 2253 27.5:4.5 2485 26:2.0 2117

700:45 2271 26:2.0 2117 26:2.2 2148

Custom 001-2999 26:2.2 2148 Custom 01-2999

26:3.8 2322

26:4.7 2403

Custom 01-2999

*Default

The letters indicate the order in which to

push the buttons.

More than one arrow means you should

push the button until you see the value

you want.

Press and hold until next digit ﬂashes to

switch to next digit or ﬁeld.

1. Computer

2. Battery cover

3. 31.8mm handlebar shim

4. Out front mount

5. CR2032 battery

6. 22.2, 25.4 & 26.0mm handlebar shim

Rear button

• Press the rear button once to enter

Primary setup.

• Press and hold the rear button 5 seconds

to enter Pairing and Advanced setup.

• Press the rear button for 5 seconds to

exit either setup mode.

• In Ride mode you can press the rear

button for 5 seconds to return you to the

beginning of the Primary setup without

changing any previously entered settings.

NOTE: Do not use the rear button while riding.

It will restart setup mode.

Primary setup

CUSTOM

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Press and hold until number

ﬂashes to switch between

hours and minutes.

BPM

RPM

KPH

MPH

3...

BPM

RPM

KPH

MPH

Eng

Deu

Fra

Esp

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Road

Mtb

City

BPM

RPM

KPH

MPH

24 Hr

12 Hr

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

3...

BPM

RPM

KPH

MPH

3...

NOTE: Custom wheel size

is the circumference of the

wheel in mm. See Wheel

size chart.

AC button

• Press the AC button for a ‘hard reset’ to return the computer to the factory default settings.

Front button

• Press the front button to scroll through the screens to ﬁnd your desired setting.

Bontrager RIDEtime Elite Computer plus Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info