714522
28
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
EN
28
Assembly
www.bora.com
Connect the exhaust air duct [7] installed on-site to the
exhaust air arc [6].
Seal the duct connection so that it is airtight using
adhesive sealing tape UDB1.
Fasten the cooktop using the mounting brackets [8] at
the worktop.
Afterwards, insert the stainless steel grease filter [4]
and air inlet nozzle [3].
Seal the surrounding gap with a black heat-resistant
silicone sealing compound.
6.8 Establishing the power
connection
Observe all safety and warning information (see Safety
chapter).
Observe all national and regional laws and regulations
as well as the supplementary regulations of the local
utility companies.
INFO The power connection must only be
implemented by a certified engineer. He/she
also assumes responsibility for the proper
installation and commissioning.
INFO Connection via plug-in contacts, e.g. plugs with
earthing contacts, are not allowed.
INFO The device complies with IEC 61000-3-12
Switch off the main switch/automatic circuit breaker
before connecting the cooktop.
Protect the main switch/automatic circuit breaker
from being switched on without permission.
Make sure the device is not energised.
Only connect the cooktop using a permanent
connection to a type H 05 VV-F power supply line
with appropriate minimum cross section (s. Tab. Fuse
protection and minimum cross section).
Connection Fuse protection Minimum
cross-section
Three-phase-connection 3 x 16 A 2.5 mm
2
Two-phase-connection 2 x 16 A 2.5 mm
2
One-phase-connection 1 x 32 A 4 mm
2
Tab. 6.2 Fuse protection and minimum cross section
For surface installation
Make sure that the sealing tape is resting on the
worktop.
For flush installation
Make sure that the sealing tape of the cooktop is
sealed well all the way round.
1
2
Fig. 6.34 Height adjustment plates
[1] Cooktop
[2] Height adjustment plates
If necessary insert height adjustment plates [2].
54321
8
5
7
6
1
Fig. 6.35 Connecting the exhaust air duct + secure
[1] Cooktop
[2] Suction opening
[3] Air inlet nozzle
[4] Stainless steel grease filter
[5] Worktop cut-out
[6] Exhaust air arc
[7] Exhaust air duct
[8] Mounting bracket
28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bora BIU wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bora BIU

Bora BIU Bedienungsanleitung - Deutsch - 44 seiten

Bora BIU Bedienungsanleitung - Holländisch - 44 seiten

Bora BIU Bedienungsanleitung - Französisch - 48 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info