Bedienungsanleitung Bora CFI11 Classic (Seite 16 von 28) (Englisch)

714395

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Installation

www.bora.com

5 Installation

 Observe all safety and warning information (see the

Safety section).

 Follow the enclosed manufacturer’s information.

INFO The device must not be installed above cooling

devices, dishwashers, stoves, ovens, washing

machines or dryers.

INFO The contact surface of the worktops and wall

sealing strips must be made of a heat-resistant

material (up to approx. 100°C).

INFO Worktop cut-outs must be moisture-sealed

using suitable means or, where necessary,

fitted with a thermal insulator.

INFO If the induction glass ceramic wok is used, the

groove dimensions must be increased to 7mm

for flush installation!

5.1 Checking the scope of delivery

Name Quantity

Operating and installation instructions 1

Cooktop fixing screws set 1

Sealing tape 1

Cooktop 1

Glass ceramic scraper 1

Height adjustment plate set 1

Mounting straps set for cooktop 1

Glass ceramic cleaning instructions 1

Tab. 5.1 Scope of delivery

 Check the scope of delivery for damage and make sure

it is complete (see Tab. 5.1).

 If there are any missing or damaged parts, please

notify BORA After Sales Service.

 Do not under any circumstances install parts which are

damaged.

 Dispose of transport packaging in the proper manner

(see the Decommissioning and Disposal section).

5.2 Tool and aids

The following tools are required for the correct installation

of the cooktop:



Phillips screwdriver Z2



Silicone for sealing cutting surfaces

5.3 Assembly instructions

5.3.1 Safety clearances

 Maintain the following safety clearances:

Fig. 5.1 Recommended minimum clearances

[1] Rear minimum clearance of 50 mm between the worktop

cut-out and the rear edge of the worktop.

[2] Minimum clearance of 300 mm from the left and right of the

worktop cut-out to the adjacent cabinet or wall.

[3] Minimum clearance of 650 mm between the worktop

and the wall unit. A minimum clearance of 1,000 mm is

recommended for ergonomic reasons.

5.3.2 Work surface and kitchen units

 Create the worktop cut-out taking the specified cut-out

dimensions into account.

 Make sure that the cutting surfaces of the worktops

are properly sealed.

 Observe the instructions provided by the worktop

manufacturer.



Cross bars on the unit in the area of the worktop cut-

out may need to be removed.



Cable protection (false floor) should be mounted

below the appliances. This needs to be removable for

maintenance work.



The drawers and/or shelves in the floor unit must be

removable.



A return flow aperture > 500 cm

is required in the

kitchen units for recirculation appliances (e.g. by

shortening the plinth boards or using suitable slatted

plinths).

5.3.3 Cooktop air intake

The components in the cooktop which generate heat are

automatically cooled. The warm air is extracted by fans

(cold air flow).

INFO In order to retain the full functionality of

the cooktop in the long term, there must be

sufficient ventilation underneath the cooktop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bora CFI11 Classic Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bora CFI11 Classic

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info