Bedienungsanleitung Bora CIW11 Classic (Seite 18 von 28) (Englisch)

714399

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Installation

www.bora.com

 Check that the cooktop is positioned correctly.

 Once all of the installation work is complete, seal the

devices with black, heat-resistant silicone sealant.

5.6 Power connection

 Observe all safety and warning information in the

Safety section.

 Observe all national and regional laws and regulations

as well as the supplementary regulations of the local

utility companies.

INFO The power connection may only be established

by a certified specialist. He/she also assumes

responsibility for the proper installation and

commissioning.

The power supply line for use (pre-assembled) must be of

the type H05VV-F or H05VVH2-F as a minimum.



Cross-section: 3G 1.5 mm²



If the connection line has been damaged this must be

replaced by a special connection line. This may only

be done by an authorised member of the After Sales

Service team.

Establishing the power connection

 Switch off the main switch/automatic circuit breaker

before connecting the cooktop.

 Secure the main switch/automatic circuit breaker

against being switched back on without permission.

 Make sure the power to the appliance is disconnected.

 Connect the mains cable.

 Only connect the cooktop using a permanent

connection to a power supply cable.

N PE

220 - 240 V~

Fig. 5.12 Connection diagram 1-phase

 Check that the cooktop has been correctly installed.

 Switch on the main switch/automatic circuit breaker.

 Put the cooktop into operation (see the Operation section).

 Check that all the functions are working correctly.

5.7 Handover to user

Once installation is complete:

 Explain the main functions to the user.

 Explain all safety-related aspects of operation and

handling to the user.

 Provide the user with the accessories and operating

and installation instructions for safe storage.

INFO The cooktop [1] lies on the side rail of the

cooktop extractor [2], which stabilises it

(exception: induction glass ceramic wok).

 Precisely position the cooktop [1].

 If necessary, use the height adjustment plates to

adjust the cooktop’s installation height.

Fig. 5.10 Cooktop and height adjustment plates

[1] Cooktop

[2] Height adjustment plates

For surface mounting

 Make sure that the sealing tape for the cooktop is flat

against the worktop.

For flush installation

 Make sure that the sealing tape of the cooktop is

sealed well all the way round.

Fig. 5.11 Mounting brackets

[1] Mounting bracket

[2] Washer

[3] Screw

 Affix the cooktop using the mounting brackets [1].

 Use the screw [3] and the washer [2] to tighten the

mounting brackets with max. 10 Nm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bora CIW11 Classic Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bora CIW11 Classic

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info