Bedienungsanleitung Bora CKFI (Seite 53 von 64) (Englisch)

714388

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Cleaning and Maintenance

www.bora.com

Cleaning in the dishwasher

 Place the components face down in the dishwasher.



No water should be able to gather in the grease filter

components.

 Wash on a programme with a maximum temperature

of 65 °C.



If it is no longer possible to clean the grease filter

completely, it must be replaced.

9.3.3 Fitting the components

Assembling the grease filter unit

INFO It is not necessary to apply pressure when

assembling the components. The grease filter

unit is designed so that the individual parts can

be assembled without force and with no room for

error.

 Carefully insert the grease filter into the tray.

 Ensure that the lock clicks into place.

 Do not force the grease filter into the tray.



If you notice any resistance whilst inserting the grease

filter, you just need to turn it around.

Fitting the grease filter unit

INFO The grease filter unit can only be fully inserted

without resistance if it is facing the right way.

If the instructions are followed correctly, it is

impossible to fit it incorrectly.

 Carefully insert the grease filter unit into the cooktop

extractor.

 Do not force the grease filter unit into the cooktop

extractor.



If you notice any resistance whilst inserting the grease

filter unit, you just need to turn it around.

Fitting the air inlet nozzle

 Insert the air inlet nozzle.

 Make sure it is positioned correctly.

9.3.4 Replacing the recirculated air filter

In recirculation mode, an additional activated carbon

filter is used. The activated carbon filter absorbs cooking

odours. The activated carbon filter is installed on the

plinth fan or the duct system.

INFO Regularly replace the activated carbon filter.

The service life can be found in the operating

instructions for the relevant activated carbon

filter.

INFO You can obtain activated carbon filters from your

specialist supplier or by contacting BORA via the

website at http://www.bora.com.

 Tilt the air inlet nozzle [1] from its horizontal position.

 Remove the air inlet nozzle [1] with your other hand.

Removing the grease filter unit

Fig. 9.2 Removing the grease lter unit

 Remove the grease filter unit.

 To do this, use the handle inside the grease filter unit.

Disassembling the grease filter unit

Fig. 9.3 Removing the grease lter

 Remove the grease filter from the tray.

 To do this, push in the 2 locking tabs on each end of

the filter.

9.3.2 Cleaning the components

The air inlet nozzle, grease filter and tray can be cleaned

manually or in a dishwasher.

 Disassemble the grease filter unit prior to cleaning.

Manual cleaning

 Use a cleaner and degreaser in one.

 Rinse the components with hot water.

 Clean the components with a soft brush.

 Rinse the components well after cleaning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bora CKFI Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bora CKFI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info