Bedienungsanleitung Bora CKG (Seite 33 von 64) (Englisch)

714393

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Operation

www.bora.com

Fig. 6.1 Standard display after switching on

INFO The menu button does not appear after switching

on if there is still residual heat in one of the

cooking zones.

INFO When the childproofing feature is active, the

lock button lights up after system start. The

standard display is only shown when it has been

deactivated (also see Childproofing feature).

INFO If

appears in the display after switching

on the system, the basic configuration is stil

incomplete and must be carried out (see Initial

operation chapter).

6.3.3 Switching off

 Long press on the power button until acoustic

signal is heard



The switching off animation appears and the display

goes out.

The cooktop extractor was switched on:



The fan symbol flashes and the automatic after-run

function is started.



As soon as the after-run period is over, the switching

off animation appears and the display goes out.

The cooktop was switched on:



In the case of previously active and still hot cooking

zones, the residual heat symbol lights up in signal

red and

is displayed.



The display goes out when no more residual heat is

present.

INFO The system can be switched off at any time: Long

press on the power button

INFO In recirculation mode the recirculated air affects

the gas cooktop.

If the gas flame goes out, is excessively affected

by the extractor and/or the flame is not as it

should be (e.g. soot production, flame blowback,

etc.), the return flow aperture must be enlarged.

6.2 Touch control

INFO The system recognises 3 different touch

commands. It differentiates between brief

touches (tap), longer contact (long press) and

vertical swiping movements with your finger

(swipe).

Touch command applicable to Time

(contact)

Tap (touch briefly) Buttons + slider 0.065 – 0.95 s

Long press (hold down) Buttons + slider 1 – 8 s

Swipe (vertical movement) Slider 0.15 – 8 s

Tab. 6.1 Touch control

If touch commands do not work or are not working

properly, the following should be taken into account:

 Tap the touch zones with only one finger.

 Ensure that no other parts of your hand are touching

the operating panel when using the controls.

 Keep the contact area as small as possible when using

the touch zones.

 Make sure that your fingers are clean and dry before

using the touch controls.

6.3 Operating the system

6.3.1 Operating principle

Operation Command

Tap a function Activating a function

Long press on a function Deactivating a function*

Swipe (slider) Setting a value (e.g. power level)

Tab. 6.2 Operating principle

6.3.2 Switching on

 Long press on the power button until acoustic

signal is heard



The icon lights up and the switching-on animation is

shown in the slider.



Once the system has started successfully, the standard

display appears in the operating panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bora CKG Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bora CKG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info