Bedienungsanleitung Bora Pro PKT11 (Seite 20 von 32) (Englisch)

714356

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Installation

www.bora.com

5 4

Fig. 5.20 Cooking zone connection in 180° installation

[1] Cooktop

[2] Rear cooking zone (zone 2)

[3] Front cooking zone (zone 1)

[4] Rear cooking zone control knob (zone 2)

[5] Front cooking zone control knob (zone 1)

 Connect the connection on the back of the left control

knob [5] to the “zone 1” connection on the back of the

cooktop [1].

 Connect the connection on the back of the right

control knob [4] to the “zone 2” connection on the

back of the cooktop [1].

 Using the configuration menu, set the correct

allocation of the cooking zones in the control

knob display (see Configuration menu, 0° or 180°

installation).

Connecting the automatic extraction system

 Connect the cooktop extractor to the cooktop using the

connector provided for the automatic extraction system.

5.5.6 Establishing the power connection

 Observe all safety and warning information (see the

Safety chapter).

 Observe all national and regional laws and regulations

as well as the supplementary regulations of the local

utility companies.

INFO The power connection may only be established by

certified specialists. The specialist also assumes

responsibility for the proper installation and

commissioning.

INFO This appliance is intended to be operated on

a supply network with an impedance Zmax at

the transfer point (mains connection) of 0.104

ohms maximum. The user is to ensure that the

appliance is only operated on a mains supply

network which meets this requirement. If

necessary, ask the local energy supply company

about the system impedance.

The power supply line to be used (pre-assembled) must

be at least Type SiHF.

(see table Fuse protection and minimum cross-section.

Connection Fuse protection Minimum

cross-section

1-phase connection 1 x 25 A

2.5 mm

2-phase connection 2 x 16 A

2.5 mm

Tab. 5.4 Fuse protection and minimum cross-section



If the connection cable has been damaged this must

be replaced. This may only be done by an authorised

member of the After Sales Service team.

 Switch off the main switch/automatic circuit breaker

before connecting the cooktop.

 Secure the main switch/automatic circuit breaker

against being switched back on without permission.

 Make sure the power to the appliance is disconnected.

 Only connect the cooktop using a permanent

connection to a power supply cable.

L1 L2

N PE

220 - 240 V~

Fig. 5.21 Connection diagram 2-phase

2 3

N PE

220 - 240 V~

Fig. 5.22 Connection diagram 1-phase

 Check that installation has been carried out correctly.

 Switch on the main switch/automatic circuit breaker.

 Put the cooktop into operation (see the Operation

chapter).

 Check that all the functions are working correctly.

Connecting the cooking zones when the cooktop is

installed rotated by 180°

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bora Pro PKT11 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bora Pro PKT11

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info