Bedienungsanleitung Boretti BVW 96 (Seite 90 von 96) (Deutsch, Englisch, Holländisch, Französisch)

534008

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Water connection

Water inlet connection

This appliance can be connected to either a

hot (max. 60°) or cold water supply.

With a hot water supply you can have a sig-

nificant reduction of energy consumption.

This however, depends on how the hot water

is produced. (We suggest alternative sources

of energy that are more environmentally

friendly as e.g. solar or photovoltaic panels

and aeolian).

For making the connection itself, the cou-

pling nut fitted to the appliance water inlet

hose is designed to screw onto a 3/4" thread

spout or to a purpose made quick-coupling

tap such as the Press-block.

The water pressure must be within the limits

given in the 'Technical data'. Your local Wa-

ter Authority will advise you on the average

mains pressure in your area.

The water inlet hose must not be kinked,

crushed, or entangled when it is being con-

nected.

The locknut must be correctly fitted to avoid

water leaks.

If the appliance is connected to new pipes or

pipes which have not been used for a long

time, you should run the water for a few mi-

nutes before connecting the inlet hose.

Do not use connection hoses which

have previously been used on an old ap-

pliance.

This appliance has been fitted with safe-

ty features which will prevent the water

used in the appliance from returning

back into the drinking water system. This

appliance complies with the applicable

plumbing regulations.

Water inlet hose with safety valve

After connecting the double-walled water in-

let hose, the safety valve is next to the tap.

Therefore the water inlet hose is only under

pressure while the water is running. If the wa-

ter inlet hose starts to leak during this oper-

ation, the safety valve cuts off the running

water.

Please take care when installing the water

inlet hose:

• The electrical cable for the safety valve is

in the double-walled water inlet hose. Do

not immerse the water inlet hose or the

safety valve in water.

• If water inlet hose or the safety valve is

damaged, remove the mains plug imme-

diately.

• A water inlet hose with safety valve must

only be replaced by the Service Force

Centre.

Warning! Dangerous voltage

Water drain connection

The end of the drain hose can be connected

in the following ways:

1. To the sink outlet spigot, securing it to the

underside of the work surface. This will

prevent waste water from the sink run-

ning into the machine.

2. To a stand pipe provided with venthole,

minimum internal diameter 4 cm.

max 85 cm

min 40 cm

max 400 cm

The drain hose can face either to the right or

left of the dishwasher

Ensure the drain hose is not bent or squash-

ed as this could prevent or slow down the

discharge of water.

The sink plug must not be in place when the

machine is draining as this could cause the

water to syphon back into the machine.

If you use a drain hose extension, its internal

diameter must be no smaller than the diam-

eter of the hose provided.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Boretti BVW 96 Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info